Subtask 32-12-16-865-052
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34 121VU HYDRAULIC/G HYD/PUMP ENG1/CTL 1701GK R35 121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 1702GK R34
1EFF : ALL 1 32-12-16Page 409 1 1 May 01/00 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 32-12-16-991-001, 402/TASK 32-12-16-991-002) Subtask 32-12-16-420-050
A. Installation of the Control Cable (10) to the Angle Joint (17) WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,
_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Put the control cable (10) in position in the brackets (8) and (15). Make sure that the brackets (8) and (15) are between the washers (31).
(5)
TORQUE the locknuts (9) and (16) to 3 m.daN (22.12 lbf.ft).
(6)
Safety the locknuts (9) and (16) with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
(7)
Apply SPECIAL MATERIALS (Material No. 05-002) to the bolts (14) and if necessary the spacers (12).
(8)
Install the clamps (13): NOTE : Make sure that the control cable (10) has a minimum bend
____
radius of 100 mm (3.9370 in.).
FOR 2804GM
-
put the clamps (13) in position and install the spacers (12), the
bolts (14) and the nut (11).
FOR 2805GM
-
put the clamps (13) in position and install the bolts (14) and the nuts (11).
1EFF : ALL 1 32-12-16Page 410 1 1 May 01/00R 1 1 1CES 1
Adjustment of the Control Cable 2804GM (2805GM) Figure 402/TASK 32-12-16-991-002
1EFF : 1 1R 1CES ALL 1 11 1 32-12-16 Page 411 May 01/00
(9) Make sure that the locknuts (33) and (34) are loose.
(10)
Make sure that the ends of the inner cable (32) are between the inspection holes of the sliding end assemblies (30).
(11)
Turn the rod end (1) and the angle joint (17) fully in to give a minimum cable length.
(12)
Turn the rod end (1) and the angle joint (17) out 2 turns.
(13)
Connect the angle joint (17) to the control handle (21) and install the washer (20) and the nut (19).
Subtask 32-12-16-420-054
B. Installation of the Control Cable to the Lever (2) WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1)
Apply SPECIAL MATERIALS (Material No. 05-002) to the bush (7), the bolt (6) and the washer (3).
(2)
Put the rod end (1) in position in the lever (2) and make sure that the holes are aligned.
(3)
If necessary turn both sliding end assemblies (30) an equal amount to align the holes.
(4)
Make sure that the rod end (1) is in position in the lever (2) and install the bush (7), the bolt (6), the washer (3) and the nut (4).
(5)
Make sure that the ends of the inner cable (32) are between the inspection holes in the sliding end assemblies (30).
(6)
Make sure that the rod end (1) and the angle joint (17) are in safety.
WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,
_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(7)
TORQUE the locknuts (34) to 0.3 m.daN (26.54 lbf.in).
(8)
Safety the locknuts (34) with corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.
1EFF : ALL 1 32-12-16Page 412 1 1 May 01/00R 1 1 1CES 1
(9) TORQUE the locknuts (33) to 0.6 m.daN (53.09 lbf.in).
(10)
Safety the nut (4) with a new cotter pin (5).
(11)
Safety the nut (19):
FOR 2804GM
