(b)
Turn the nut (31) to adjust the parallelism.
(c)
Manually open the forward door of the nose landing gear.
(d)
Tighten the nut (33) but do not fully TORQUE it at this time.
(6)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 32-22-00Page 520 1 1 May 01/05 1 1 1CES 1
(7)
Make sure that:
-
the gap U is between 8.5 mm (0.3346 in.) and 11.5 mm (0.4527 in.).
-
the gap R is between 2.5 mm (0.0984 in.) and 5.5 mm (0.2165 in.).
-
the gap V is between 5.5 mm (0.2165 in.) and 8.5 mm (0.3346 in.).
(8)
Manually open the forward doors of the nose landing gear.
(9) Do again the adjustment of the lateral gaps if necessary. R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
Subtask 32-22-00-820-053-A
G. Adjust the lateral gaps of the leg door.
(Ref. Fig. 502/TASK 32-22-00-991-005)
**ON A/C 062-099, 151-199, 204-212,
(Ref. Fig. 503A/TASK 32-22-00-991-007-A) R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 503B/TASK 32-22-00-991-007-B) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(1)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
(2)
Measure the gap U.
(3)
Manually open the forward doors of the nose landing gear.
(4)
Adjust the transversal gap U to between 0 mm (0.0000 in.) and 3 mm (0.1181 in.) with the washer (38).
(a)
Remove the nut (27) and the washer (28).
(b)
Remove the bolt (40) and the washer (38).
(c)
Find the correct number of washers (38) to get the gap U (washer thickness 0.5 mm (0.0196 in.). )
1EFF : ALL 1 32-22-00Page 521 1 1 Aug 01/05 1 1 1CES 1
(d)
Install the washers (38), the bolt (40), the washer (28) and the nut (27).
(e)
Tighten the nut (27) but do not fully TORQUE it at this time.
(5)
Adjust the parallelism of the leg door in relation to the forward doors with the nut (31):
(a)
Manually close one forward door of the nose landing gear so that it touches the forwad stop.
(b)
Turn the nut (31) to adjust the parallelism.
(c)
Manually open the forward door of the nose landing gear.
(d)
Tighten the nut (33) but do not fully TORQUE it at this time.
(6)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
(7)
Make sure that:
-
the gap U is between 0 mm (0.0000 in.) and 3 mm (0.1181 in.).
-
the gap R is between 2.5 mm (0.0984 in.) and 5.5 mm (0.2165 in.).
-
the gap V is between 5.5 mm (0.2165 in.) and 8.5 mm (0.3346 in.).
(8)
Manually open the forward doors of the nose landing gear.
(9) Do again the adjustment of the lateral gaps if necessary.
**ON A/C ALL
Subtask 32-22-00-820-054
H. Adjust the gap Q between the leg door roller and the stop with the rod ends (34) and (37). (Ref. Fig. 502/TASK 32-22-00-991-005)
R **ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 503/TASK 32-22-00-991-007) R **ON A/C 062-099, 151-199, 204-212,
(Ref. Fig. 503A/TASK 32-22-00-991-007-A)
1EFF : ALL 1 32-22-00Page 522 1 1 May 01/05 1 1 1CES 1R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 503B/TASK 32-22-00-991-007-B)
**ON A/C ALL
(1)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
(2)
Measure the gap Q.
(3)
Manually open the forward doors of the nose landing gear.
(4)
Adjust the gap Q to between 0.83 mm (0.0326 in.) and 2.83 mm (0.1114 in.).
(a)
Remove the nut (24), the washer (23) and the screw (22).
(b)
Remove the nut (27), the washer (28), the bolt (40) and the washers (38).
(c)
Disconnect the rod ends (34) and (37) from the leg of the nose landing gear.
(d)
Adjust symmetrically the rod ends (34) and (37) to get the dimension Q between 0.83 mm (0.0326 in.) and 2.83 mm (0.1114 in.).
(e)
Tighten the nuts (33) and (36) but do not TORQUE and safety them at this time.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(141)
