(10)
Install the screws (23) and loosely install the nuts (21).
(11)
Hold the mounting plate (22) in the position identified before removal.
(12)
Tighten the nuts (21) and the nut (24).
(13)
Safety the nut (24) with a new cotter pin (25).
(14)
Apply SEALANTS (Material No. 09-016) to the heads of the screws (23) and the nuts (24) and (21).
(15)
Install the applicable secondary-hinged-fairing attachment (Ref. TASK 57-26-21-400-001).
(16)
Install the applicable secondary hinged fairing (Ref. TASK 32-12-13-400-001).
Subtask 32-12-00-420-067
B. Installation of the MLG Fixed Fairing Assembly and Attachments
(Ref. Fig. 405/TASK 32-12-00-991-016)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
(1)
Clean the component interfaces and/or the adjacent area.
(2)
Do an inspection of the component interfaces and/or the adjacent area.
1EFF : ALL 1 32-12-00Page 445 1 1 Nov 01/00R 1 1 1CES 1
(3)
Make sure that the parts retained from the removed components are clean and in the correct condition.
(4)
Remove and discard the cotter pin (6) from the nut (5).
(5)
Remove the nut (5), the washer (4) and the bolt (3) from the bracket (1).
(6)
Install the bonding strap (2), the bolt (3), the washer (4) and the nut (5) (Ref. TASK 20-28-00-912-004).
(7)
Safety the nut (5) with a new cotter pin (6).
(8)
Apply SEALANTS (Material No. 09-016) to the head of the bolt (3) and the nut (5).
(9)
Remove and discard the lockwire from the bolts (8) and (10).
(10)
Remove the bolt (10) and the washer (11) from the bracket (7).
(11)
Install the bonding strap (9), the washer (11) and the bolt (10) (Ref. TASK 20-28-00-912-004).
(12)
Safety the bolts (8) and (10) with MISCELLANEOUS (Material No. 19-010).
(13)
Apply SEALANTS (Material No. 09-016) to the heads of the bolts (8) and (10).
(14) Install the fixed fairing assembly (Ref. TASK 32-12-14-400-002). Subtask 32-12-00-865-071
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 1GG, 2GG, 3GG, 4GG, 52GA, 1701GK, 1702GK, 3700GD, 3701GD.
5. Close-up
________ Subtask 32-12-00-860-070
A. Aircraft Maintenance Configuration Put the aircraft back to the ground configuration (Ref. TASK 32-00-00-860-002).
(1) Depressurize the Green hydraulic system
(Ref. TASK 29-10-00-864-001).
1EFF : ALL 1 32-12-00Page 446 1 1 Nov 01/00R 1 1 1CES 1
(2) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
Subtask 32-12-00-942-064
B. Removal of Equipment
(1)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
1EFF : ALL 1 32-12-00Page 447 1 1 Nov 01/00R 1 1 1CES 1
TASK 32-12-00-440-005
Restoration of the Aircraft after Flight with a Failed or Missing Ground Door Opening Cable
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R Refer to the MMEL TASK: 32-12-01 R Main Gear Doors R Ground Opening Cable
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(18)
