4. Procedure
_________
(Ref. Fig. 401/TASK 32-22-00-991-008) Subtask 32-22-00-020-054
A. Removal of the NLG Main Doors and Attaching Parts
(1)
Remove the two main doors (Ref. TASK 32-22-11-000-001).
(2)
Remove the two aft doors (Ref. TASK 32-22-13-000-001).
(3)
Remove the NLG main door control rods (Ref. TASK 32-31-41-000-001).
(4)
Remove the two rotating rods (Ref. TASK 32-22-16-000-001).
(5)
Retain all the attaching parts from the doors and the rods.
(6) Disconnect and retain all the bonding straps. Subtask 32-22-00-860-062
B. ECAM Display during Flight without NLG Doors
(1) You can ignore the ECAM displays that follow (for the applicable missing NLG door).
(a) With the landing-gear normal control-lever (6GA) in DOWN position (landing gear extended).
1_ ECAM WHEEL page
- Door position hinge-bar-DOOR IN TRANSIT.
- Landing gear locked down-Green triangles.
2 ECAM warning (flight phases 2, 6 and 7)
_
-
L/G DOOR NOT CLOSED
-
L/G LGCIU 1 FAULT or
-
L/G LGCIU 2 FAULT or
-
L/G LGCIU 1 + 2 FAULT
NOTE : The LGCIU warnings, will only occur if LGCIU 1 and /or
____ 2 are reset above 70 kts (or if a power interrupt occurs above 70 kts).
1EFF : ALL 1 32-22-00Page 402 1 1 Aug 01/98 1 1 1CES 1
NLG Main Door Assy
Figure 401/TASK 32-22-00-991-008
1EFF : ALL 1 32-22-00 Page 403
1 1 Aug 01/98
1 1
1CES 1
5. Close-up
________ Subtask 32-22-00-860-063
A. Put the aircraft back to its initial configuration.
(1)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2)
Remove the access platform(s).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
In the cockpit, install a temporary placard to tell the crew that the NLG main doors are removed.
1EFF : ALL 1 32-22-00Page 404 1 1 Aug 01/98 1 1 1CES 1
TASK 32-22-00-440-001 Restoration of the A/C after flight without NLG Main Doors Assy
1.
Reason for the Job
__________________
CDL 52-09
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-11-400-001 Installation of the Main Door Assy 32-22-13-400-001 Installation of the Aft Door Assy 32-22-16-400-001 Installation of the Rotating Rod 32-31-41-400-001 Installation of the NLG main door control rod
3. Job Set-up
__________ Subtask 32-22-00-860-064
A. Safety Precautions
(1) Put the safety barriers in position.
4. Procedure
_________ Subtask 32-22-00-420-054
A. Installation of the NLG Doors and Attaching Parts
(1)
Install the two rotating rods (Ref. TASK 32-22-16-400-001).
(2)
Install the two aft doors (Ref. TASK 32-22-13-400-001).
1EFF : ALL 1 32-22-00Page 405 1 1 Aug 01/98 1 1 1CES 1
(3)
Install the two main doors (Ref. TASK 32-22-11-400-001).
(4)
Install the NLG main door control rods (Ref. TASK 32-31-41-400-001).
5. Close-up
________ Subtask 32-22-00-860-065
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(134)
