曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (2) Remove the nuts (7) and (10).
 (3) Remove the washers (6) and (11).
 (4) Remove the WASHER SPACER (M46789).
 (5) Remove the washers (3) and (4).
 Subtask 32-21-18-420-054
 C. Installation of one NLG Lock Spring
 (1) Install the TENSIONING FIXTURE (M21929) on the spring (5).
 (2) Put the spring (5) and the washer (4) on the pin (2).
 (3) Use the applicable adjustment washers (3) to get the clearance : J1 = between 0.05 mm (0.0019 in.) and 0.5 mm (0.0196 in.).
 (4) Install the adjustment washers (3), the washer (4), the spring (5), the washer (6) and the nut (7).
 (5) TORQUE the nut (7) to between 0.8 and 0.95 m.daN (70.79 and 84.07 lbf.in).
 NOTE : Put a wrench on the flats of the shoulder of the pin (2) to____ prevent movement.
 (6) Install a new cotter pin (8).
 (7) Make sure that the bushing (12) is in the correct position on the pin (13).
 (8) Install the spring (5).
 (9) Install the washer (11).

 

 (10)
 Install the nut (10). TORQUE the nut (10) to between 0.8 and 0.95 m.daN (70.79 and 84.07 lbf.in).

 (11)
 Install a new cotter pin (9).

 (12)
 Remove the TENSIONING FIXTURE (M21929) from the spring (5).

 (13)
 Apply SEALANTS (Material No. 09-001) at the zones E.

 5. Close-up
________ Subtask 32-21-18-410-050
 A. Get Access
 (1)
 Remove the warning notice(s).

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Close the doors of the nose landing gear (Ref. TASK 32-22-00-410-001).

 1EFF : ALL 1 32-21-18Page 415 1 1 Feb 01/98 1 1 1CES 1

 BEARING ASSY - SWIVEL - REMOVAL/INSTALLATION
____________________________________________ TASK 32-21-24-000-001 Removal of the Swivel Bearing WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
 CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.

 WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY
_______
 OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.

 WARNING : PRESSURIZE ONLY THE HYDRAULIC SYSTEM(S) THAT IS (ARE) NECESSARY FOR
_______ THE TASK. ISOLATE THE OTHER HYDRAULIC SYSTEM(S) BEFORE YOU SUPPLY HYDRAULIC POWER TO THE AIRCRAFT.
 WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______
 YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.7 m (5 ft. 7 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
21-26-42-000-001 Removal of the Avionics Equipment Ventilation Duct 32-21-11-000-002 Removal of the NLG Leg Assy (2526GM) R 32-21-24-991-001-A Fig. 401
 1EFF : ALL 1 32-21-24Page 401 1 1 Nov 01/02 1 1 1CES 1

 3. Job Set-up
__________
 Subtask 32-21-24-010-050

 A. Get Access
 (1)
 Remove the nose landing gear (Ref. TASK 32-21-11-000-002).

 (2)
 Open the access door 824 to get access to the hinge points of the nose gear.

 (3)
 Put the access platform in position in zone 123.

 (4)
 Remove the avionics equipment ventilation duct (Ref. TASK 21-26-42-000-001).

 4. Procedure
_________ R (Ref. Fig. 401/TASK 32-21-24-991-001-A) Subtask 32-21-24-020-052
 A. Removal of the Swivel Bearing
 (1)
 Remove the cotter pins (7), the nuts (8), the washers (6), the protective cover (5) and the seals (3) and (4).

 (2)
 Remove the bolts (1).

 (3)
 Remove the swivel bearing (2).

 1EFF : ALL 1 32-21-24Page 402 1 1 Nov 01/02 1 1 1CES 1

R R  Nose Gear Swivel Bearing Figure 401/TASK 32-21-24-991-001-A
 1EFF : 1 1 1CES  ALL  1 111 32-21-24 Page 403 Nov 01/02

 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(104)