(2)
On the panel 400VU:
-
make sure that the landing-gear control-lever (6GA) is in the DOWN position
-
make sure that the warning notice is in position to tell persons not to operate the landing gear controls.
(3)
Put the safety barriers at the limits of the MLG travel ranges.
(4)
Make sure that the access platform is in position.
(5)
Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on the applicable MLG lockstay actuator (Ref. TASK 32-00-00-481-001).
1EFF : ALL 1 32-12-14Page 424 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-12-14-860-054
B. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is below the applicable MLG.
(2)
If electrical power is necessary do the flight configuration precautions (Ref. TASK 32-00-00-860-001), before you jack the aircraft.
(3)
Lift the aircraft on jacks (Ref. TASK 07-11-00-581-001).
4. Procedure
_________
Subtask 32-12-14-420-058
A. Preparation For Installation
(1)
Clean the component interfaces and/or the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
R **ON A/C 001-049, 051-060, 101-101,
Subtask 32-12-14-560-050
B. Preparation For a Replacement Component (Ref. Fig. 402/TASK 32-12-14-991-002, 403/TASK 32-12-14-991-001)
(1)
Remove and discard the lockwire from the lock nuts (10) and (29).
(2)
Loosen the lock nuts (10) and (29).
(3)
Adjust the eye-ends (3) out of the spools (2) so that the dimension W is between 44.0 mm (1.7322 in.) and 46.0 mm (1.8110 in.).
(4)
Remove the bolts (5) and the washers (4).
(5)
Remove and discard the lockwire from the lock nuts (12).
1EFF : ALL 1 32-12-14Page 425 1 1 May 01/05 1 1 1CES 1
R Fixed Fairing - Installation Figure 403/TASK 32-12-14-991-001
1EFF : 001-049, 051-060, 101-101, 1 32-12-14Page 426 1 1 Aug 01/05 1 1 1CES 1
(6) Loosen the lock nuts (12) so that the studs (20) can turn. Make sure that the serrated plates (16) do not disengage. Subtask 32-12-14-420-059 R C. Installation of a Replacement MLG Fixed Fairing Assembly
(Ref. Fig. 403/TASK 32-12-14-991-001)
WARNING : THE WEIGHT OF THE FIXED FAIRING IS 34kg (75lb).
_______
(1)
Hold the fixed fairing (1) in position on the MLG.
(2)
At the position C, install the bush (21), the bolt (27), the washer
(22) and the nut (23).
(3)
Install the RIGGING SPACER (98D32104083000) on the bolt (27), this will make sure that the dimensions Z and Y are correct. They must be between 1.3 mm (0.0511 in.) and 2.7 mm (0.1062 in.). (Ref. Fig. 402/TASK 32-12-14-991-002)
(4)
At the position F, install the bush (26), the bolt (27), the washer
(22) and the nut (23).
(5)
Install the second RIGGING SPACER (98D32104083000) on the bolt (27), this will make sure that the dimensions Z and Y are correct. They must be between 1.3 mm (0.0511 in.) and 2.7 mm (0.1062 in.).
(6)
Install the bolts (9), the washers (8) and the nuts (7).
(7)
Temporarily tighten the lock nuts (12). This will cause the MLG fixed fairing (1) to become stable during MLG retraction.
(8)
Slowly retract the applicable MLG (Ref. TASK 32-30-00-867-001). During retraction of the MLG make sure that the fixed fairing (1) does not overlap the lower wing surface.
(9)
Remove the lock nuts (12), the locking devices (13) and (14) and the outer serrated plates (16).
(10)
Turn the studs (20) so that they are fully into the rod-ends (28).
(11)
Turn the spools (2) to get the dimensions that follow: (Ref. Fig. 404/TASK 32-12-14-991-003)
(a) The dimension V must be between 2.5 mm (0.0984 in.) and 9.5 mm (0.3740 in.).
1EFF : 001-049, 051-060, 101-101, 1 32-12-14Page 427 1 1 Aug 01/05 1 1 1CES 1
R Fixed Fairing - Installation
Figure 403A/TASK 32-12-14-991-001-C
1EFF : 301-399, 1 32-12-14 Page 428
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(42)
