(2)
 On the steering handwheels (CAPT and F/O) and on the brake pedals put warning notice(s) in position to tell persons not to operate them.

 (3) Put the safety barriers in position.
 Subtask 32-21-27-860-050

 B. Aircraft Maintenance Configuration
 (1)
 On the panel 110VU, make sure that the PARK BRK control switch is in the OFF position.

 (2)
 Make sure that the wheel chocks are in position.

 (3)
 Lift the aircraft at the forward jacking point (Ref. TASK 07-11-00-581-003).

 (4)
 Remove the nose wheel which prevents the removal of the pin of the lower arm (Ref. TASK 32-41-12-000-001).

 (5)
 Remove the protective sealants with a spatula to prevent damage to the surfaces of the components.

 1EFF : ALL 1 32-21-27Page 403 1 1 May 01/05 1 1 1CES 1

 4. Procedure
_________ R **ON A/C 001-004, 052-054, 106-149, 229-299, 303-399, 401-499,
 Subtask 32-21-27-020-055
 A. Removal of the Torque Link Assy
 (1) Disconnect the upper electrical harness from the torque link assembly **ON A/C 001-004, 052-054,
 (Ref. Fig. 401/TASK 32-21-27-991-004) R **ON A/C 001-004, 052-054, 106-149, 229-299, 303-399, 401-499,
 (a)
 Remove the nut (103). NOTE : Use a flat spanner to make sure that the screw (100) does

____
 not turn.

 (b)
 Remove the clamp (101) and the washer (102).

 (c)
 Disconnect the connector (90) and install the blanking caps.

 (d)
 Remove the nut (98), the washer (97), the bolt (94), the support

 (96) and the clamp (95).

 (e)
 Disengage the upper electrical harness of the torque link assembly through the hole of the protector (91).

 (2) Disconnect the lower electrical harness from the torque link assembly **ON A/C 001-004, 052-054,
 (Ref. Fig. 401/TASK 32-21-27-991-004) R **ON A/C 001-004, 052-054, 106-149, 229-299, 303-399, 401-499,
 (a) Remove the nuts (111), the washers (110), the screw (100) and the bolt (104).
 1EFF : ALL 1 32-21-27Page 404 1 1 Aug 01/05 1 1 1CES 1

 Electrical Harness
 Figure 401/TASK 32-21-27-991-004

R 1EFF : 001-004, 051-054, 1 32-21-27Page 405 1 1 May 01/05 1 1 1CES 1

 (b) Disengage the lower electrical harness and its support (99) from the torque link assembly.
 (3)
 Remove the related fittings from the torque link assembly

 (a)
 Remove the nut (112), the bolt (93), the washers (92) and (113) and the protector (91).

 (b)
 Remove the nuts (105), the washers (106), the bolts (109) and the washers (108). Remove the stop (107).

 (4)
 Disconnect the center hinge
 (Ref. Fig. 402/TASK 32-21-27-991-001)

 (a)
 Remove the cotter pin (9) from the nut (8).

 (b)
 Remove the nut (8), the washer (7) and the screw (10).

 (c)
 Hold the shaft (1) and remove the nut (6) and the washer (5).

 (d)
 Remove the shaft (1) with a plastic drift.

 (e)
 Remove the washers (4), (3) and (2).

 (5) Remove the lower arm
 **ON A/C 001-004, 052-054,

 (Ref. Fig. 403/TASK 32-21-27-991-002) R **ON A/C 106-149, 229-299, 303-399, 401-499,
 (Ref. Fig. 403A/TASK 32-21-27-991-002-A) R **ON A/C 001-004, 052-054, 106-149, 229-299, 303-399, 401-499,
 (a)
 Remove and discard the cotter pin (24).

 (b)
 Remove the nut (25) and the support (23).

 (c)
 Remove the screw (22) with a soft drift.

 (d)
 Remove the lower shaft (26) with the EXTRACTOR (J47563).

R 1EFF : 001-004, 052-054, 106-149, 229-299, 1 32-21-27Page 406 1303-399, 401-499, 1Aug 01/05 1 1 1CES 1

 Nose Gear Torque Links - Center Hinge Figure 402/TASK 32-21-27-991-001 
R 1EFF : 1 1 1CES  ALL  1 111 32-21-27 Page 407 May 01/05

 Nose Gear Torque Links - Lower Hinge
 Figure 403/TASK 32-21-27-991-002

R 1EFF : 001-004, 051-054, 1 32-21-27Page 408 1 1 May 01/05 1 1 1CES 1

 Nose Gear Torque links - Lower Hinge
 Figure 403A/TASK 32-21-27-991-002-A

R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-21-27Page 409 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (e) Remove the lower arm of the torque link and the washers (20) and (21).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(108)