(2)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 32-22-00Page 406 1 1 Aug 01/98 1 1 1CES 1

 TASK 32-22-00-040-002 Preparation of the A/C for flight without one or two NLG Aft Door Assy WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
 WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY

_______
 OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.

 1.
 Reason for the Job

__________________
 CDL 52-10.

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.7 m (5 ft. 7 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-13-000-001 Removal of the Aft Door Assy
 32-22-16-000-001 Removal of the Rotating Rod

 **ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
 32-22-00-991-009 Fig. 402 R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
 32-22-00-991-009-A Fig. 402A
 1EFF : ALL 1 32-22-00Page 407 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 32-22-00-010-053

 A. Get Access
 (1) Put the access platform in position below the NLG doors.
 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,

 (Ref. Fig. 402/TASK 32-22-00-991-009) R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
 (Ref. Fig. 402A/TASK 32-22-00-991-009-A)
 **ON A/C ALL

 Subtask 32-22-00-020-052
 A. Removal of the NLG Aft Doors and Attaching Parts
 (1)
 Remove the NLG aft doors (Ref. TASK 32-22-13-000-001).

 (2)
 Remove the NLG rotating rods (Ref. TASK 32-22-16-000-001).

 (3)
 Retain all the attaching parts from the doors and the rotating rods. NOTE : The hinge point attachment bolts must not stay on the

____ aircraft.
 (4) Disconnect and retain all the bonding straps.
 NOTE : The NLG leg door can be missing or not.

____
 1EFF : ALL 1 32-22-00Page 408 1 1 Aug 01/05 1 1 1CES 1

 NLG Aft Door Assy
 Figure 402/TASK 32-22-00-991-009

R 1EFF : 001-049, 051-099, 101-105, 151-156, 1 32-22-00Page 409 1201-209, 1May 01/05 1 1 1CES 1

 NLG Aft Door Assy Figure 402A/TASK 32-22-00-991-009-A
R 1EFF : 106-149, 157-199, 210-299, 301-399, 1 32-22-00Page 410 1401-499, 1Aug 01/05 1 1 1CES 1

 5. Close-up
________ Subtask 32-22-00-860-055
 A. Put the aircraft back to its initial configuration.
 (1)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 (2)
 Remove the access platform.

 (3)
 In the cockpit, install a temporary placard to tell the crew that the NLG aft doors are removed.

 (4)
 Make sure that the work area is clean and clear of tool(s) and other items.

 1EFF : ALL 1 32-22-00Page 411 1 1 Aug 01/01R 1 1 1CES 1

 TASK 32-22-00-440-002 Restoration of the A/C after flight without one or two NLG Aft Door Assy
 1.
 Reason for the Job

__________________
 CDL 52-10.

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.7 m (5 ft. 7 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-13-400-001 Installation of the Aft Door Assy 32-22-16-400-001 Installation of the Rotating Rod
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(135)