C. Safety Precautions
(1)
Obey the flight configuration precautions (Ref. TASK 32-00-00-860-001).
(2)
Put the access platform in position.
(3)
Put the warning notices in position to tell persons not to pressurize the Green hydraulic system: - on the panel 40VU in the cockpit, - on the ground service panel of the Green hydraulic system.
1EFF : ALL 1 32-12-15Page 402 1 1 May 01/05R 1 1 1CES 1
Subtask 32-12-15-865-053
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R 49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34 121VU HYDRAULIC/G HYD/PUMP ENG1/CTL 1701GK R35 121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 1702GK R34
4. Procedure
_________
(Ref. Fig. 401/TASK 32-12-15-991-001)
Subtask 32-12-15-020-050
A. Removal of the Control Unit (11)
(1)
Put the RIGGING PIN through the actuating lever and into the bypass valve 2517GM (2518GM).
(2)
Remove and discard the lockwire from the locknut (3).
(3)
Loosen the locknut (3).
(4)
Remove and discard the cotter pin (6).
(5)
Remove the nut (7), the washer (8) and disconnect the angle joint (4) from the support (5).
(6)
Disengage the control cable (2) from the bracket (1) and move it away from the control unit (11).
(7)
Remove the bolts (9), the washers (10) and remove the control unit (11).
1EFF : ALL 1 32-12-15Page 403 1 1 Feb 01/99 1 1 1CES 1
Control-Unit - MLG Door Ground-Opening
Figure 401/TASK 32-12-15-991-001
1EFF : ALL 1 32-12-15 Page 404
1 1 Feb 01/98
1 1
1CES 1
TASK 32-12-15-400-001
Installation of the Control Units that Open/Close the MLG Doors
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______
ONLY WITH A GOOD SUPPLY OF AIR.
OBEY THE MANUFACTURERS INSTRUCTIONS.
PUT ON PROTECTIVE CLOTHING.
DO NOT GET THEM IN YOUR MOUTH.
DO NOT SMOKE.
DO NOT BREATHE THE GAS.
THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______
YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notices R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 98DNSA20208040 1 RIGGING PIN
1EFF : ALL 1 32-12-15Page 405 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 32-12-15Page 406 1 1 May 01/05 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
No specific Material No. 05-002 Material No. 09-005 corrosion-resistant steel lockwire 0.8 mm (0.032 in.) dia.USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
FOR CSN 32-12-15 01-001 6 cotter pin FOR CSN 32-12-15 02-001 6 cotter pin 32-12-16 01A-01532-12-16 02A-015
D. Referenced Information
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(49)
