R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-018 USA AMS 3267/3
CORROSION INHIBITING LOW ADHESION SEALANT
(Ref. 20-31-00)
Material No. 09-019 USA AMS 3267/3
LOW ADHESION CORROSION INHIBITING SEALANT
(Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
1EFF : ALL 1 32-12-14Page 410 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
4 cotter pins 52-81-13 01 -005
4 cotter pins 52-81-13 01L-005
5 cotter pins 52-81-13 01 -005
5 cotter pins 52-81-13 01L-005
12 cotter pin 32-11-11 80 -005
12 cotter pin 32-11-11 80C-005
13 cotter pin 32-11-11 80 -005
13 cotter pin 32-11-11 80 -045
13 cotter pin 32-11-11 80C-005
13 cotter pin 32-11-11 80C-045
14 cotter pin 32-11-11 80 -045
14 cotter pin 32-11-11 80C-045
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-12-14-400-002 Installation of a Replacement MLG Fixed Fairing Assembly
R **ON A/C 001-049, 051-060, 101-101,
32-12-14-991-005 Fig. 401
1EFF : ALL 1 32-12-14Page 411 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 061-099, 102-149, 151-199, 201-299, 401-499,
32-12-14-991-005-B Fig. 401A
**ON A/C 051-060, 301-399,
Post SB 52-1100 For A/C 051-060,
32-12-14-991-005-C Fig. 401B
**ON A/C 001-049, 051-060, 101-101,
32-12-14-991-002 Fig. 402
R **ON A/C 051-099, 102-149, 151-199, 201-299, 301-399, 401-499, Post SB 52-1100 For A/C 051-060, 32-12-14-991-002-A Fig. 402A **ON A/C ALL
3. Job Set-up
__________
Subtask 32-12-14-941-054
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
On the panel 400VU:
-
make sure that the landing-gear control-lever (6GA) is in the DOWN position
-
make sure that the warning notice is in position to tell persons not to operate the landing gear controls.
1EFF : ALL 1 32-12-14Page 412 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-12-14-860-053
B. Aircraft Maintenance Configuration
(1)
Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on the applicable MLG lockstay actuator (Ref. TASK 32-00-00-481-001).
(2)
Make sure that the access platform is in position below the applicable zone 733(743).
4. Procedure
_________
**ON A/C 001-049, 051-060, 101-101,
(Ref. Fig. 401/TASK 32-12-14-991-005) R **ON A/C 061-099, 102-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401A/TASK 32-12-14-991-005-B)
**ON A/C 051-060, 301-399,
Post SB 52-1100 For A/C 051-060,
(Ref. Fig. 401B/TASK 32-12-14-991-005-C) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 32-12-14-420-057
A. Preparation For Installation
(1)
Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架3(38)
