(g)
 Put blanking caps on the disconnected hose unions (20) and (31) and the hoses (25) and (26).

 (6)
 Disconnect the locksprings at their top attachment (Ref. TASK 32-11-19-000-003).

 (7)
 Install the SPLINT ASSEMBLY - SIDE STAY (98D32104013001) on the side-stay assembly (19) with:

 -
the cables to the wing surface

 -
the strap to the wing surface

 -
the center-joint of the side-stay located in the center hole of the side-stay splint assembly.

 (8)
 Tighten the strap and connect the cables to the hook.

 (9)
 Remove the blanking cap from the aft face of the integral cross tube on the upper part of the MLG main fitting.

 NOTE : Be careful when you remove the bolt (4) as it is possible for
____ it to fall inside the MLG leg assembly.
 (10) Remove the cotter pin (9), the nut (10), the washers (8), the bracket R (7) and the bolt (4). Discard the cotter pin (9) and the bolt (4).
 (11)
 Carefully disengage the cardan bracket (3) from the MLG leg assembly.

 (12)
 Compress the lockstay actuator to fold the lockstay and safety the lockstay in this position.

 (13)
 Remove the circlip (17) as follows:
 (Ref. Fig. 404/TASK 32-11-16-991-007)

 NOTE : Make sure that all the related parts are clean before you
____
 remove the circlip (17).

 1EFF : 001-003, 051-052, 1 32-11-16Page 419 1 1 Aug 01/05 1 1 1CES 1

 (a)
 Use an applicable tool to release the tail of the circlip (17) from the key slot of the lock washer (16).

 (b)
 Hold the tail of the circlip (17) with a pair of thin-nose pliers.

 (c)
 Carefully pull the circlip (17) in a clockwise direction until it releases from the chamfered slot in the nut (15).

 (14)
 Remove the lock washer (16) from the nut (15).

 (15)
 Use the TUBE SPANNER (460005834) and remove the nut (15) and the washer (14) from the cardan joint (18).

 (16)
 Loosen the strap (but not fully) on the side-stay splint assembly.

 (17)
 Move the side-stay around the side-stay center-joint so that the cardan joint (18) comes out of the MLG attachment lugs.

 (18)
 Remove the circlip (36) as follows: NOTE : Make sure that all the related parts are clean before you

____
 remove the circlip (36).

 (a)
 Use an applicable tool to release the tail of the circlip (36) from the key slot of the lock washer (35).

 (b)
 Hold the tail of the circlip (36) with a pair of thin-nose pliers.

 (c)
 Carefully pull the circlip (36) in a clockwise direction until it releases from the chamfered slot in the nut (34).

 (19)
 Remove the lock washer (35) from the nut (34).

 (20)
 Use the TORQUE ADAPTOR (460005812) and remove the nut (34) and the washer (33) from the cardan joint (37).

 (21)
 Move the side-stay so that the cardan joint (37) comes out of the side-stay bracket. Tighten the strap to prevent movement of the side-stay assembly (19).

 WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE MLG SIDE-STAY. IT
_______
 WEIGHS 62.5kg (137.5lb).

 (a) Lower the side-stay assembly (19) on to a trestle and remove the cables from the hook.
R 1EFF : 001-003, 051-052, 1 32-11-16Page 420 1 1 May 01/05 1 1 1CES 1

 (22)
 If the side-stay assembly (19) is to be replaced, remove the side-stay splint assembly.

 (23)
 Remove the cotter pin (11), the nut (6) and the washer (5). Discard the cotter pin (11).

 (24)
 Remove the pin (1) and the washer (2). Move the cardan bracket (3) away from the cardan joint (13) and remove the washers (12). (Ref. Fig. 403/TASK 32-11-16-991-005)

 (25) Remove the seal (54) from the bush (53). Discard the seal (54). R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 32-11-16-020-052-A
 A. Removal of the MLG Side-Stay Assembly
 (1)
 Remove the MLG actuating cylinder (Ref. TASK 32-31-46-000-001). Use a hoist that can lift 67.0 kg (147.7096 lb).

 (2)
 Disconnect the electrical connector of the cable (23) from the proximity sensor (7).

 (3)
 Remove the bolts (22), the washers (21) and the clips (20) from the bracket (24).

 (4)
 Put blanking caps on the disconnected electrical connectors.

 (5)
 Disconnect the hydraulic hoses as follows: WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(44)