B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 Material No. 04-022 Material No. 11-026 Material No. 19-003 Material No. 19-010 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R R R R R R R R 4 4 8 8 15 15 15 20 20 20 cable tie cable tie cable tie cable tie cotter pin cotter pin cotter pin cotter pin cotter pin cotter pin 32-11-11 52F-03232-11-11 52G-032 32-11-11 52F-032 32-11-11 52G-032 32-11-11 52C-005 32-11-11 52F-005 32-11-11 52G-005 32-11-11 52C-005 32-11-11 52F-005 32-11-11 52G-005
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 12-12-32-611-006 Replenishment of the MLG Torque Link Damper 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears
32-41-11-000-006 Removal of the MLG Wheel
(2649GM,2650GM,2651GM,2652GM)
32-41-11-400-006 Installation of the MLG Wheel
(2649GM,2650GM,2651GM,2652GM)
R SIL 12-008
3. Job Set-up
__________
Subtask 32-11-29-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-
make sure that the landing-gear control-lever 6GA is in the DOWN position
-
make sure that the warning notice is in position to tell persons not to operate the landing gear.
Subtask 32-11-29-860-050
B. Aircraft Maintenance Configuration
(1)
Make sure the applicable axle is on jacks (Ref. TASK 07-12-00-582-002).
(2)
Make sure the applicable MLG wheels have been removed (Ref. TASK 32-41-11-000-006).
1EFF : ALL 1 32-11-29Page 409 1 1 May 01/04 1 1 1CES 1
4. Procedure
_________
R **ON A/C 001-003, 051-052,
Subtask 32-11-29-420-051
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Do an inspection of the component interface and/or the adjacent area.
NOTE : In the step that follows, make sure that the Materials No.
____ 04-004 and No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
(4) Lubricate the items that follow with COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022):
-
the threads of the bolts (1)
-
the washers (2)
-
the spacer assembly (3)
-
the spacers (4), (10) and (12)
-
the torque link pin (6)
-
the sleeves (9) and (11)
-
the nut (13)
-
the mating surfaces of the torque link damper (5)
-
the hinge points of the top and bottom torque link assemblies.
Subtask 32-11-29-420-050
B. Installation of the Torque Link Damper
(1)
Install the sleeve (9) in the top torque link assembly and the sleeve
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(108)
