Torque-Link Damper-Assembly
Figure 604/TASK 32-11-27-991-006
1EFF : ALL 1 32-11-27 Page 624
1 1 May 01/04
1 1
1CES 1
(1)
Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).
(2)
Make sure that the level indicator shows a level between the REFILL line and the FULL line. If the torque link damper is at the REFILL position fill the damper (Ref. TASK 12-12-32-611-006).
(3)
Examine the torque link dampers to make sure that:
-
there are no hydraulic leaks between the reservoir and the damper
-
there is no external damage of the damper assembly
-
the bolts are correctly safetied with lockwire
-
the cover is correctly installed and is not damaged
-
the labels and indicator level lines are clean and in the correct condition.
5. Close-up
________
Subtask 32-11-27-942-054
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-11-27Page 625 1 1 May 01/04 1 1 1CES 1
DAMPER - TORQUE LINK ASSY, MLG (2823GM,2824GM) - REMOVAL/INSTALLATION
_____________________________________________________________________ TASK 32-11-29-000-001 Removal of the Torque Link Damper 2823GM, 2824GM WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice 460007242 1 TORQUE REACTION ADAPTOR
1EFF : ALL 1 32-11-29Page 401 1 1 May 01/04R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-41-11-000-006 Removal of the MLG Wheel (2649GM,2650GM,2651GM,2652GM)
**ON A/C 001-003, 051-052,
32-11-29-991-001 Fig. 401 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
32-11-29-991-001-B Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-11-29-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
Subtask 32-11-29-582-050
B. Lift the Axle
(1) Lift the applicable MLG axle (Ref. TASK 07-12-00-582-002).
1EFF : ALL 1 32-11-29Page 402 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-11-29-010-050
C. Get Access
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(106)
