B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 32-00-00-481-001 Installation of the Safety Devices on the Landing
 Gears
 32-11-13-000-001 Removal of the MLG Shock Absorber

R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 401-499,
 32-11-13-991-005-A Fig. 404
 **ON A/C 051-052,
 32-11-13-991-005 Fig. 404A
 **ON A/C 301-399,
 32-11-13-991-005-B Fig. 404B
 **ON A/C ALL
 3. Job Set-up
__________
 Subtask 32-11-13-941-055
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Make sure that the safety devices are installed on the landing gear (Ref. TASK 32-00-00-481-001).

 (3)
 On the panel 400VU:

 -make sure that the landing gear control lever 6GA is in the DOWN position
 -put a warning notice in position to tell persons not to operate the landing gear.
 1EFF : ALL 1 32-11-13Page 444 1 1 Aug 01/05 1 1 1CES 1

 (4)
 Put the warning notices in the cockpit to tell persons not to operate the brakes.

 (5)
 Put the warning notices in position on the ground hydraulic services connections to tell persons not to operate:

 -the Green hydraulic system
 -the Yellow hydraulic system.
 Subtask 32-11-13-860-059

 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the applicable hydraulic systems are depressurized (Ref. TASK 29-00-00-864-001).

 (2)
 Make sure that the applicable hydraulic reservoirs are depressurized (Ref. TASK 29-14-00-614-001).

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 32-11-13-010-051
 C. Get Access
 (1)
 Remove the applicable MLG shock absorber (Ref. TASK 32-11-13-000-001).

 (2)
 Use the LIFTING TACKLE (460006211) to install the MLG shock absorber in the BUILD TROLLEY (460006212).

 **ON A/C 301-399,
 Subtask 32-11-13-010-051-A
 C. Get Access
 (1)
 Remove the applicable MLG shock absorber (Ref. TASK 32-11-13-000-001).

 (2)
 Use the LIFTING TACKLE (460006211) to install the MLG shock absorber in the BUILD TROLLEY (460007240).

 1EFF : ALL 1 32-11-13Page 445 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 4. Procedure
_________ R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 404/TASK 32-11-13-991-005-A)
 **ON A/C 051-052,

 (Ref. Fig. 404A/TASK 32-11-13-991-005)
 **ON A/C 301-399,

 (Ref. Fig. 404B/TASK 32-11-13-991-005-B) R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 32-11-13-020-051-A
 A. Removal of the MLG Shock-Absorber Gland-Seals
 (1)
 Lift and hold the diaphragm tube assembly (3).

 (2)
 Move the bearing (15) out of its groove to get access to the pins

 (14) and (17).

 (3)
 Hold the retaining collar (16). Use the ASSEMBLY AND EXTRACTION TOOL (460006409) to remove the pins (14) and (17).

 (4)
 Remove the retaining collar (16).

 (5)
 Remove the upper diaphragm tube assembly (3).

 (6)
 Remove the bearing (15).

 (7)
 Remove the upper bearing housing (18) with the attached parts.

 (8)
 Remove the lower bearing housing (4).

 (9)
 Remove and discard the wiper ring (13).

 1EFF : ALL 1 32-11-13Page 446 1 1 Aug 01/05 1 1 1CES 1

 MLG Shock-Absorber Gland-Seals - Location and Detail Figure 404/TASK 32-11-13-991-005-A
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 32-11-13Page 447 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R MLG Shock-Absorber Gland-Seals - Location and Detail R Figure 404A/TASK 32-11-13-991-005

R 1EFF : 051-052, 1 32-11-13Page 448 1 1 May 01/05 1 1 1CES 1

 MLG Shock-Absorber Gland-Seals - Location and Detail R Figure 404B/TASK 32-11-13-991-005-B
R 1EFF : 301-399, 1 32-11-13Page 449 1 1 May 01/05 1 1 1CES 1

 (10)
 Remove the internal gland seals:
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM LANDING GEAR 起落架2(27)