(a) Remove and discard the seals (8) and (9), the joint seal (11) and the sealing ring (10).
(11)
Remove the external gland seals:
(a) Remove and discard the seals (7) and the backing rings (6).
(12) Remove and discard the seals (1) and (2). **ON A/C 051-052,
Subtask 32-11-13-020-051
A. Removal of the MLG Shock-Absorber Gland-Seals
(1)
Lift and hold the diaphragm tube assembly (3).
(2)
Move the bearing (14) out of its groove to get access to the pins
(13) and (16).
(3)
Hold the retaining collar (15). Use the ASSEMBLY AND EXTRACTION TOOL (460006409) to remove the pins (13) and (16).
(4)
Remove the retaining collar (15).
(5)
Remove the upper diaphragm tube assembly (3).
(6)
Remove the bearing (14).
(7)
Remove the upper bearing housing (17) with the attached parts.
(8)
Remove the lower bearing housing (4).
(9)
Remove and discard the wiper ring (12).
(10)
Remove the internal gland seals:
(a) Remove and discard the seals (8) and (9), the joint seal (11) and the sealing ring (10).
(11)
Remove the external gland seals:
(a) Remove and discard the packings (7) and the retainers (6).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-13Page 450 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R (12) Remove and discard the seals (1) and (2). **ON A/C 301-399,
Subtask 32-11-13-020-051-B
A. Removal of the MLG Shock Absorber Gland-Seals
(1)
Release the tab-washers (5).
(2)
Remove the screws (4), and remove and discard the tab-washers (5).
(3)
Remove the lock-plate (6) from the upper bearing housing (7).
(4)
Use the PIN SPANNER (460007253) to release the upper bearing housing (7).
(5)
Remove the upper bearing housing (7) and the upper diaphragm tube assembly (3) from the sliding tube assembly (11).
(6)
Remove the pins (9) from the two-part stop (8).
(7)
Remove the two-part stop (8) from inside the upper bearing housing (7).
(8)
Remove the lower bearing housing (10) from the sliding tube assembly (11).
(9)
Remove and discard the wiper ring (17).
(10)
Remove the internal gland seals:
(a) Remove and discard the seals (12) and (13), the joint seal (15) and the sealing ring (14).
(11)
Remove the external gland seals:
(a) Remove and discard the seals (19) and the backing rings (18).
(12)
Remove and discard the seals (1) and (2).
R 1EFF : 051-052, 301-399, 1 32-11-13Page 451 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL
TASK 32-11-13-400-003
Installation of the MLG Shock-Absorber Gland-Seals
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : WHEN YOU DO A MAINTENANCE TASK THAT USES COMMON GREASE, USE ONLY
_______ GREASES OF THE SAME SPECIFICATION (IT IS PERMITTED TO USE DIFFERENT BRANDS IF THEIR SPECIFICATIONS ARE THE SAME). DO NOT MIX GREASES THAT HAVE CLAY THICKENERS WITH GREASES THAT HAVE LITHIUM THICKENERS. THIS MIXTURE CAN CHANGE THE LUBRICATION PROPERTIES OF THE GREASE. IF YOU USE GREASES OF DIFFERENT TYPES (SPECIALLY THOSE WITH CLAY THICKENERS AND LITHIUM THICKENERS), DECREASE THE SERVICE INTERVALS OF THE AIRCRAFT (BY HALF, FOR EXAMPLE) SPECIFIED IN THE MAINTENANCE PLANNING DOCUMENT. DO THIS FOR APPROXIMATELY THREE OR FOUR SERVICES (REFER TO YOUR IN-SERVICE DATA TO FIND THE NUMBER OF SERVICES BEST ADAPTED TO YOUR AIRCRAFT).
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific smooth edged tool
No specific warning notice
No specific warning notices
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 15.00 to 82.00 m.daN
(120.00 to 600.00 lbf.ft) 460003180-74 1 KEEP RING 460006211 1 LIFTING TACKLE
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(28)
