R 1EFF : 051-052, 301-399, 1 32-11-13Page 476 1 1 May 01/05 1 1 1CES 1
(7)
Remove the upper diaphragm tube-assembly (3) with the attached parts.
(8)
Remove the lower bearing housing (10) with the attached parts.
(9)
Remove and discard the wiper ring (17).
(10)
Remove the internal gland seals:
(a) Remove and discard the seals (12) and (13), the joint seal (15) and the sealing ring (14).
(11)
Remove the external gland seals:
(a) Remove and discard the retainers (18) and the packings (19).
(12)
Remove and discard the seals (1) and (2).
(13)
Release the lock washer (24).
(14)
Remove the sliding tube sub-assembly (25) from the BUILD TROLLEY.
(15)
Use the TORQUE ADAPTER (460006404) to remove the jacking dome (23).
(16)
Remove and discard the lock washer (24).
(17)
Remove the tube assembly (20) from the sliding tube sub-assembly (25).
(18)
Remove and discard the O-ring (21) and the backing ring (22).
R 1EFF : 301-399, 1 32-11-13Page 477 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL
TASK 32-11-13-400-004
Installation of the Sliding Tube Sub-Assembly of the MLG Shock Absorber
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : WHEN YOU DO A MAINTENANCE TASK THAT USES COMMON GREASE, USE ONLY
_______ GREASES OF THE SAME SPECIFICATION (IT IS PERMITTED TO USE DIFFERENT BRANDS IF THEIR SPECIFICATIONS ARE THE SAME). DO NOT MIX GREASES THAT HAVE CLAY THICKENERS WITH GREASES THAT HAVE LITHIUM THICKENERS. THIS MIXTURE CAN CHANGE THE LUBRICATION PROPERTIES OF THE GREASE. IF YOU USE GREASES OF DIFFERENT TYPES (SPECIALLY THOSE WITH CLAY THICKENERS AND LITHIUM THICKENERS), DECREASE THE SERVICE INTERVALS OF THE AIRCRAFT (BY HALF, FOR EXAMPLE) SPECIFIED IN THE MAINTENANCE PLANNING DOCUMENT. DO THIS FOR APPROXIMATELY THREE OR FOUR SERVICES (REFER TO YOUR IN-SERVICE DATA TO FIND THE NUMBER OF SERVICES BEST ADAPTED TO YOUR AIRCRAFT).
1. Reason for the Job__________________
Self Explanatory
R 1EFF : ALL 1 32-11-13Page 478 1 1 May 01/05 1 1 1CES 1
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
No specific warning notices
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 15.00 to 82.00 m.daN
(120.00 to 600.00 lbf.ft) 460006211 1 LIFTING TACKLE 460006212 1 BUILD TROLLEY 460006404 1 TORQUE ADAPTER 460006405 1 ASSEMBLY SLEEVE 460007240 1 BUILD TROLLEY 460007279 1 PIN SPANNER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM LANDING GEAR 起落架2(35)
