-the MLG spare-seal activating-valve has been closed.
 NOTE : It is recommended that ALL gland seals on the applicable MLG

____ are replaced at a subsequent scheduled maintenance procedure.
 Subtask 32-11-13-611-051
 B. Check the Contents of the MLG Shock Absorber
 (1) Make sure that the contents of the MLG shock absorber are at the correct level (Ref. TASK 12-12-32-611-004).
 1EFF : ALL 1 32-11-13Page 207 1 1 May 01/05R 1 1 1CES 1

 Spare-Seal Activating-Valve Figure 202/TASK 32-11-13-991-004
 1EFF : 1 1R 1CES  ALL  1 11 1 32-11-13 Page 208 May 01/05

 5. Close-up
________ Subtask 32-11-13-942-052
 A. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 1EFF : ALL 1 32-11-13Page 209 1 1 May 01/05R 1 1 1CES 1

 TASK 32-11-13-860-002 To Open the Spare-Seal Activating-Valve WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1.
 Reason for the Job

__________________
 To reactivate the lower gland seals after gland seal replacement

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  safety barriers
 No specific warning notices R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific  lockwire, corrosion resistant steel 0.8 mm (0.032 in) dia.
 1EFF : ALL 1 32-11-13Page 210 1 1 May 01/05 1 1 1CES 1

 C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
1  cap screw  32-11-11 65A-180
 1  cap screw  32-11-11 65C-180
 1  cap screw  32-11-11 65D-180
 D. Referenced Information
 ------------------REFERENCE  -------------------------------DESIGNATION ------------------------------

-------------------------------------------------------------------------------32-11-13-991-004 Fig. 202
 3. Job Set-up
__________ Subtask 32-11-13-941-053
 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Put a warning notices in the cockpit to tell persons not to operate the landing gear.

 4. Procedure
_________
 (Ref. Fig. 202/TASK 32-11-13-991-004) Subtask 32-11-13-860-053
 A. To Open the Spare-Seal Activating-Valve
 (1)
 Remove and discard the lockwire from the spindle (2).

 (2)
 Turn the spindle (2) counter-clockwise by hand to its stop, to open the spare-seal activating-valve.

 (3)
 Install the cap screw (1).

 (4)
 Torque the cap screw (1) to between 0.4 and 0.45 m.daN (35.39 and

 39.82 lbf.in).
 1EFF : ALL 1 32-11-13Page 211 1 1 May 01/05 1 1 1CES 1

 (5)
 Safety the cap screw (1) with lockwire, corrosion resistant steel 0.8

 mm (0.032 in) dia..

 (6)
 Make a note in the aircraft technical log that the spare-seal activating-valve has been opened.

 5. Close-up
________ Subtask 32-11-13-942-053
 A. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Make a record in the aircraft log that the spare-seal
 activating-valve is open.

 1EFF : ALL 1 32-11-13Page 212 1 1 May 01/05 1 1 1CES 1 SHOCK ABSORBER ASSY - MLG - REMOVAL/INSTALLATION
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(13)