(2)
 Install the axle adaptor-sleeves (Ref. TASK 32-42-71-400-001).

 (3) Install the tachometers (Ref. TASK 32-42-57-400-001).
 **ON A/C 051-099,

 Subtask 32-11-13-560-050-B
 A. Preparation of a Replacement Shock Absorber
 (1)
 Install the 1M and 2M system harnesses in the axle (Ref. TASK 32-11-43-400-003). Make sure that the cables are in the correct position.

 (2)
 Install the axle adaptor-sleeves (Ref. TASK 32-42-71-400-001).

 (3)
 Install the tachometers (Ref. TASK 32-42-57-400-001).

 (4)
 Install the TPIS rotating mechanisms (Ref. TASK 32-49-18-400-001).

 (5)
 Install the brake fan assemblies (Ref. TASK 32-48-51-400-005).

 1EFF : ALL 1 32-11-13Page 429 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 301-399, 401-499,

 Subtask 32-11-13-560-050-A
 A. Preparation of a Replacement Shock Absorber
 (1)
 Install the 1M and 2M system harnesses in the axle (Ref. TASK 32-11-43-400-003). Make sure that the cables are in the correct position.

 (2)
 Install the axle adaptor-sleeves (Ref. TASK 32-42-71-400-001).

 (3)
 Install the tachometers (Ref. TASK 32-42-57-400-001).

 (4) Install the brake fan assemblies (Ref. TASK 32-48-51-400-005).
 **ON A/C 001-003, 051-052,

 Subtask 32-11-13-420-054-A
 B. Preparation For Installation
 (1)
 Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 If necessary, install new MLG gland-seals (Ref. TASK 32-11-13-400-003).

 (5)
 Lubricate the new O-rings, backing rings and seals that you install, with HYDRAULIC FLUIDS (Material No. 02-001) or HYDRAULIC FLUIDS (Material No. 02-004) before you install them.

 (6)
 Install the new seal (36) and the new seal (37) on the shock absorber (1).

 (7)
 Install the new O-rings (56) and the new backing rings (55) on the gland housing (57).

R 1EFF : 001-003, 051-052, 301-399, 401-499, 1 32-11-13Page 430 1 1 Aug 01/05 1 1 1CES 1

 (8)
 Install the new O-ring (40) and the new backing rings (39) on the inflation valve assembly (41). Use the RING - KEEP (460003180-24) to get them back to their initial dimensions.

 (9)
 Install the new packer (46) on the charging valve (45).

 (10)
 Install the new backing ring (61) and the new O-ring (62) on the valve stem (63).

 (11)
 Apply a thin layer of SPECIAL MATERIALS (Material No. 05-047) to:

 -
the washer (38)

 -
the pin (30)

 -
the collar (32)

 -
the interface and the stem (area 'N') of the inflation valve assembly (41)

 -
the external surface of the gland housing (57) (area 'M').

 Subtask 32-11-13-420-053-A
 C. Installation of the MLG Shock Absorber Assembly
 WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE MLG SHOCK-ABSORBER.
_______
 ITS WEIGHT CAN BE AS MUCH AS 118kg (260lb).

 (1)
 Put the shock absorber (1) in position on the 200 kg (440 lb) hand-operated forklift (angle of lift +10 to -10 degrees).

 (2)
 Put the hand-operated forklift below the MLG main fitting.

 (3)
 Adjust the lift angle of the forklift so that you lift the shock absorber (1) along the centerline of the MLG main fitting.

 (4)
 Install the shock absorber (1) fully in the MLG leg.

 (5)
 Install the gland housing (57) as follows:

 (a)
 Install the gland housing (57) in the MLG leg. Use the SPANNER-PEG (460006465) to align the holes in the gland housing (57) with the holes in the MLG leg.

 (b)
 Install the new:

 -
tab washer (47)

 -
tab washer (53)

 -
tab washer (54)

 -retaining pins (48).
R 1EFF : 001-003, 051-052, 1 32-11-13Page 431 1 1 May 01/05 1 1 1CES 1

 (c)
 TORQUE the retaining pins (48) to between 9.5 and 10.0 m.daN

 (70.05 and 73.74 lbf.ft).

 (d)
 Safety the retaining pins (48) with the tab washers (47), (53) and (54).

 (e)
 Install the bonding straps (50) with the bolts (49), the washers
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(22)