8. BITE Test
_________
 The BITE has these functions, it:
 -continuously monitors its system for failures
 -sends failure data to other interface systems (maintenance and warnings)
 -keeps a record of failures
 -automatically does specified test of the systems, or part of the system, at specified times
 -lets specified tests be done during ground maintenance.
 The BITE in the computers is described in these chapters:
 -
the BSCU in (Ref. 32-46-00)

 -
the LGCIU in (Ref. 32-62-00).

 -
the TPIS in (Ref. 32-49-00).

 **ON A/C 051-099,
 1EFF : ALL 1 32-00-00Page 52 1 1 Aug 01/05 1 1 1CES 1 LANDING GEAR - GENERAL - MAINTENANCE PRACTICES

______________________________________________
 TASK 32-00-00-481-001
 Installation of the Safety Devices on the Landing Gears
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  safety barriers
 No specific  warning notice
R  D23080000 1 GROUND SAFETY LOCK 460005833 1 GROUND LOCK SLEEVE 460007280 1 GROUNDLOCK SLEEVE
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
32-00-00-481-002 Installation of the Safety Devices on the Landing Gear Doors 32-00-00-991-002 Fig. 201
 1EFF : ALL 1 32-00-00Page 201 1 1 Aug 01/05 1 1 1CES 1

 3. Job Set-up
__________ Subtask 32-00-00-860-051
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice in position to tell persons not to operate the landing gear or the landing gear doors.

 (3)
 Make sure that the wheel chocks are correctly installed.

 4. Procedure
_________ (Ref. Fig. 201/TASK 32-00-00-991-002) Subtask 32-00-00-481-050
 A. Installation of the Safety Devices on the Landing Gears WARNING : MAKE SURE THAT, IF THE LANDING GEAR DOORS ARE OPEN, THEY ARE
_______ SAFETIED BEFORE YOU INSTALL THE LANDING GEAR SAFETY-DEVICES. IF THE LANDING GEAR DOORS ARE OPEN BUT NOT SAFETIED THERE IS A RISK THAT THEY CAN CLOSE AND CAUSE INJURY.
 (1) To install the MLG safety locks:
 (a)
 If a landing gear door is open, make sure:

 -
the ground door-opening handle is in the open position

 -
the ground door-safety lock is installed (Ref. TASK 32-00-00-481-002).

 (b)
 Make sure that the piston rod of the lock stay actuating cylinder is clean.

 (c)
 Remove the pin (1) and open the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280).

 (d)
 Make sure that the GROUND LOCK SLEEVE is clean and in the correct condition.

 (e)
 Put the GROUND LOCK SLEEVE in position on the piston rod of the lock stay actuating cylinder.

 (f)
 Close the GROUND LOCK SLEEVE and install the pin (1) from the inboard side.

 1EFF : ALL 1 32-00-00Page 202 1 1 Feb 01/04R 1 1 1CES 1

R  Main and Nose Landing-Gears Safety-Devices Figure 201/TASK 32-00-00-991-002
 1EFF : 1 1 1CES  ALL  1 111 32-00-00 Page 203 Feb 01/99

 (g) Make sure that the flag is in view.
 (2) To install the NLG safety lock:
 (a) If a landing gear door is open, make sure:
 -
the ground door-opening handle is in the open position

 -
the ground door-safety locks are installed (Ref. TASK 32-00-00-481-002).

 (b) Make sure that the holes in the NLG lock stay are aligned. R (c) Make sure that the GROUND SAFETY LOCK (D23080000) is in a clean
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(79)