(2)
Install the MLG brakes (Ref. TASK 32-42-27-400-001).
(3)
Install the MLG wheels (Ref. TASK 32-41-11-400-006).
1EFF : ALL 1 32-11-00Page 633 1 1 May 01/05 1 1 1CES 1
MLG Axle Inspection Areas Figure 606/TASK 32-11-00-991-022-A
1EFF : 1 1R 1CES ALL 1 11 1 32-11-00 Page 634 Feb 01/05
R **ON A/C 051-099, 301-399, 401-499,
Subtask 32-11-00-410-063-A
A. Close Access
(1)
Install the MLG axle adaptor sleeves (Ref. TASK 32-42-71-400-001).
(2)
Install the MLG brakes (Ref. TASK 32-42-27-400-001).
(3)
Install the MLG wheels (Ref. TASK 32-41-11-400-006).
(4) Install the MLG brake fans (Ref. TASK 32-48-51-400-005).
**ON A/C ALL
Subtask 32-11-00-869-058
B. Ground Configuration
(1) If necessary, put the aircraft in the ground configuration (Ref. TASK 32-00-00-860-002).
Subtask 32-11-00-942-076
C. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-11-00Page 635 1 1 Aug 01/05 1 1 1CES 1 TASK 32-11-00-220-004
Inspection of the MLG Side Stay Attachment Lug(s) after the Aircraft has gone off the Runway
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
NOTE : Make sure that you read the instructions in Task 05-51-24-200-001
____ (Inspection after Leaving Runway or Taxiway) before you do this task.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific warning notices No specific access platform 1.5 m (4 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-11-18-000-001 Removal of the MLG Side-Stay 32-11-18-400-001 Installation of the MLG Side-Stay 32-11-00-991-020 Fig. 607
1EFF : ALL 1 32-11-00Page 636 1 1 Feb 01/05R 1 1 1CES 1
3. Job Set-up
__________ Subtask 32-11-00-941-076
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
(4)
Put warning notices in position to tell persons not to operate the landing gear doors.
Subtask 32-11-00-010-066
B. Get Access
(1)
Put the access platform in position adjacent to the applicable MLG.
(2)
Disconnect the side-stay from the MLG side-stay lower attachment lug(s) and remove the lower cardan joint (Ref. TASK 32-11-18-000-001).
4. Procedure
_________ (Ref. Fig. 607/TASK 32-11-00-991-020) Subtask 32-11-00-220-065-A
A. Inspection of the MLG Side-Stay Attachment Lug
(1)
Visually examine the MLG side-stay lower attachment lug. Look for signs of cracks in the paint finish, distortion, stress and fatigue.
(2)
Measure the out-of-roundness of the internal diameter W, you must measure the two bushes. The internal diameter W must be round within 30 microns (1200 micro-inches).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(108)
