曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (b) Examine the electrical conduits, connections, connectors and protective coverings for damage and fluid contamination. If necessary, clean the contaminated area. 
R R  (c) Make sure that the electrical conduits have full protection and are in a serviceable condition. 
R  (3) Inspect the MLG actuator:
 (a) Examine the actuator for signs of hydraulic leaks.
 (b) Examine the chrome plating on the ram for wear, scoring and damage.
 (c) Examine the actuator for damage to the protective finish.
 (d) Examine the actuator for cracks, dents, distortion and wear.
 5. Close-up________
 Subtask 32-11-00-410-050
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the access platform(s).
 (3) Close the MLG doors (Ref. TASK 32-12-00-410-001).
 Subtask 32-11-00-942-051
 B. Removal of Equipment
 (1) Remove the safety barriers.
 (2) Remove the warning notice(s).

 

 (3) Remove the ground support and maintenance equipment, the special and

 standard tools and all other items.
R
 1EFF : ALL 1 32-11-00Page 607 1 1 Nov 01/04 1 1 1CES 1 TASK 32-11-00-220-003

 Detailed Dimensional Check of the MLG Lockstay Assembly
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 A dimensional check of the length of the MLG lockstay actuator after replacement of:
 -
a lockstay actuator

 -
a side-stay assembly.

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific non metallic scraper
 No specific safety barriers
 No specific warning notice
 No specific access platform 2.5 m (8 ft. 2 in.)

R No specific  Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) 460006437 1 TOOL-HOLDING 460007262 1 CHECKING GAUGE
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B
 CORROSION INHIBITING FILLET CONSISTENCY
 (Ref. 20-31-00)

 1EFF : ALL 1 32-11-00Page 608 1 1 May 01/05 1 1 1CES 1

 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
8 cotter pin  32-11-17 01 -030
R  8 cotter pin 32-11-17 01A-030 8 cotter pin 32-11-17 01B-030
 D. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
 the Ground Connector 32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-11-16-400-001 Installation of the MLG Side-Stay Assembly 2505GM,
 2506GM 32-11-21-000-001 Removal of the MLG Lockstay Actuating Cylinder 32-11-21-400-001 Installation of the MLG Lockstay Actuating Cylinder 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access CMM 321121 (for corrective action) 32-11-00-991-026 Fig. 601 32-11-00-991-024 Fig. 602
 3. Job Set-up
__________
 Subtask 32-11-00-941-062
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 On the panel 400VU:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(101)