(2)
Examine the brake attachment flanges for:
-damage to the protective finish
-corrosion or cracks on the installed bushes.
(3)
Examine the sliding tube bushes for damage to the protective finish, corrosion and/or cracks at the following locations:
-
the lower torque link attachment lug
-
the lower slave link attachment lug
-
the towing/debogging lug
-
the jacking dome.
(4)
If you find damage or corrosion, refer to (Ref. CMM 321225) for repair procedures.
**ON A/C 301-399,
Subtask 32-11-00-200-052-B
A. Detailed Inspection of MLG, Sliding Tube at Brake Attachment Flange, and other Interference Fit Bushes
(1)
Preparation for inspection:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the area to be examined.
(2)
Examine the brake attachment flanges for:
-damage to the protective finish
-corrosion or cracks on the installed bushes.
(3)
Examine the sliding tube bushes for damage to the protective finish, corrosion and/or cracks at the following locations:
-
the lower torque link attachment lug
-
the lower slave link attachment lug
-
the towing/debogging lug
-
the jacking dome.
(4)
If you find damage or corrosion, refer to (Ref. CMM 321222) for repair procedures.
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-00Page 663 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
MLG Sliding Tube-Inspection Areas Figure 611/TASK 32-11-00-991-030- 12 (SHEET 1)
R 1EFF : 1 1 1CES ALL 1 111 32-11-00 Page 664 Feb 01/05
MLG Sliding Tube-Inspection Areas Figure 611/TASK 32-11-00-991-030- 22 (SHEET 2)
1EFF : 1 1R 1CES ALL 1 11 1 32-11-00 Page 665 Feb 01/05
**ON A/C ALL
5. Close-up
________ Subtask 32-11-00-410-067
A. Close Access
(1) Install the brakes (Ref. TASK 32-42-27-400-001).
(2)
Install the wheels (Ref. TASK 32-41-11-400-006). Subtask 32-11-00-586-055
B. Lower the Aircraft
(1)
Remove the access platform(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Lower the aircraft (Ref. TASK 07-11-00-586-002). Subtask 32-11-00-942-081
C. Removal of Equipment
(1)
Close the MLG doors (Ref. TASK 32-12-00-410-001).
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : ALL 1 32-11-00Page 666 1 1 May 01/05 1 1 1CES 1 MAIN GEAR - REPAIRS
___________________
TASK 32-11-00-300-001
General Approved Repairs of the Main Landing Gear (MLG)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform
No specific safety barriers
No specific warning notice
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(115)
