1 Remove the CHECKING GAUGE (1) from the lockstay actuator.
_
 2 Remove the lockstay actuator (Ref. TASK 32-11-21-000-001).

_
 3 Adjust the lockstay actuator to the correct length in

_ accordance with the (Ref. CMM 321121).
 4 Install the lockstay actuator (Ref. TASK 32-11-21-400-001).
_
 (i)
 Do again the steps (3)(d) to (3)(g).

 (j)
 Remove the CHECKING GAUGE (1) from the lockstay actuator.

 (4) If the pin (5) has been removed and installed in step (3), do these steps:
 (a)
 Remove the nut (7) and the washer (6).

 (b)
 Hold the lockstay actuator (3.3 kg (7.28 lb)) and remove the pin (5), the washer (4) and the washers (9).

 (c)
 Install the pin (5) with the head aligned forward, the washer (4) and the washers (9).

 (d)
 Install the washer (6) and the nut (7).

 1EFF : ALL 1 32-11-00Page 614 1 1 Nov 01/04R 1 1 1CES 1

 (e)
 Use the TOOL-HOLDING (460006437) to hold the pin (5) and TORQUE the nut (7) to between 0.46 and 0.70 m.daN (40.70 and 61.94 lbf.in).

 (f)
 Safety the nut (7) with a new cotter pin (8).

 (g)
 Apply SEALANTS (Material No. 09-016) to the nut (7).

 (5) Apply SEALANTS (Material No. 09-016) to the heads of the attachment pins for the lockstay actuator.
 Subtask 32-11-00-860-056
 B. Aircraft Maintenance Configuration
 (1)
 Pressurize the Green hydraulic system reservoir (Ref. TASK 29-14-00-614-002).

 (2)
 Close the main gear doors (Ref. TASK 32-12-00-410-001).

 (3)
 If necessary, lower the aircraft off jacks (Ref. TASK 07-11-00-586-002).

 (4)
 Continue with the installation of the MLG side-stay assembly (Ref. TASK 32-11-16-400-001) or the lockstay actuator (Ref. TASK 32-11-21-400-001), as necessary.

 5. Close-up
________ Subtask 32-11-00-942-063
 A. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 32-11-00Page 615 1 1 Nov 01/04R 1 1 1CES 1

 TASK 32-11-00-200-005
 Inspection of the MLG after the Aircraft has gone off the Runway
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 NOTE : Make sure that you read the instructions in Task 05-51-24-200-001
____ (Inspection after Leaving Runway or Taxiway) before you do this task.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice
 No specific warning notices
 No specific access platform 2.5 m (8 ft. 2 in.)

R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 6.00 to 36.00 m.daN
 (50.00 to 260.00 lbf.ft) 460004331-24 1 DRIFT 460006440 1 EXTRACTOR 460006441 1 ALIGNMENT BULLET 460006442 1 HOLDING SPANNER
 1EFF : ALL 1 32-11-00Page 616 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 32-11-00Page 617 1 1 Nov 01/04 1 1 1CES 1 -------------------------------------------------------------------------------

 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-047 Material No. 09-016  C Z-11.904 ANTI COR. COMPOUND(HIGH TEMP.SILICONE SEALANT) (Ref. 20-31-00)USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(103)