(10) Do a visual inspection of the spherical bearing of the MLG rear pintle pin:
(a)
Look at the sealant that covers the bearing assembly for breaks or cracks. Broken or cracked sealant is an indication of movement or loose items.
(b)
Do an inspection of the bearing and its retaining nut for signs of movement.
(c)
Do an inspection of the bearing retaining bolt for signs of movement and make sure it is not loose.
(d)
If you find signs of movement of the bearing, do a detailed inspection of the bearing assembly (Ref. CMM 32-12-25).
**ON A/C 301-399,
Subtask 32-11-11-420-063-C
A. Preparation for Installation
(1)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that all the identification plates and labels on the MLG are correctly installed and show the correct data (Ref. TASK 11-00-00-400-012).
(4)
Make sure that the parts retained from the removed components are clean and in the correct condition.
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-11Page 449 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(5)
Remove the MLG forward pintle bearing (Ref. TASK 57-26-13-000-001).
(6)
Clean the MLG forward pintle bearing with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(7)
Make sure that the grease channels to the MLG pintle bearing are clear.
(8)
Install the MLG forward pintle bearing (Ref. TASK 57-26-13-400-001).
(9)
Do a visual inspection of the MLG rear pintle pin (Ref. TASK 57-51-00-200-001).
(10) Do a visual inspection of the spherical bearing of the MLG rear pintle pin:
(a)
Look at the sealant that covers the bearing assembly for breaks or cracks. Broken or cracked sealant is an indication of movement or loose items.
(b)
Do an inspection of the bearing and its retaining nut for signs of movement.
(c)
Do an inspection of the bearing retaining bolt for signs of movement and make sure it is not loose.
(d)
If you find signs of movement of the bearing, do a detailed inspection of the bearing assembly (Ref. CMM 32-12-22).
**ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 32-11-11-420-062
B. Installation of the MLG Leg Assembly
(Ref. Fig. 402/TASK 32-11-11-991-027)
NOTE : In the procedure that follows, make sure that the Materials No.
____ 04-004 and No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
(1)
Remove the blanking caps from the forward and the rear pintles.
(2)
Check the sleeve (15):
(a) Make sure that the internal and external surfaces of the sleeve
(15) are clean.
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 32-11-11Page 450 1301-399, 1Aug 01/05 1 1 1CES 1
(b)
Make sure that the internal surfaces of the fixed bushes are clean.
(c)
Put the sleeve (15) in position on the rear pintle pin (20) and make sure that:
-
it will fully engage
-
it moves freely.
(d)
Remove the sleeve (15) from the rear pintle pin (20).
(e)
Put the sleeve (15) in position in the fixed bush and make sure that it moves freely.
(f)
Remove the sleeve (15) from the fixed bush.
(3)
Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the internal surfaces of the fixed bushes.
(4)
Put the sleeve (15) in position in the fixed bush and make sure that:
-
it moves freely in the fixed bush
-
it is installed in the fully aft position.
(5)
Lubricate the new O-ring (31) with COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022).
(6)
Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the internal surface of the spherical bearing.
(7)
Install the new O-ring (31) in the internal groove of the spherical bearing.
(8)
Use the TOOL-PINTLE BEARING ALIGNMENT (MLG) (98D57004009000) to align the spherical bearing in the forward pintle mounting.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(129)
