(c)
Carefully pull the wire (16) (in a clockwise direction) until it releases from the chamfered slot in the nut (18).
(10)
Remove the lock-washer (17) from the nut (18).
(11)
Use the SPANNER-MLG REAR PINTLE (98D32104005000) to remove the nut
(18) and the washer (19) from the rear pintle pin (20). Subtask 32-11-11-020-050-A
E. Removal of the Pintle Pins
(Ref. Fig. 402B/TASK 32-11-11-991-027-A)
WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,
_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
CAUTION : YOU MUST REMOVE THE REAR PINTLE PIN FIRST.
_______
(1)
Remove and discard the lockwire from the half-seals (25) and (26).
(2)
Remove the half-seals (25) and (26). Make sure that the anti-rotation washer (24) has not moved.
(3)
Install the TOOL - R/I (MLG FWD AND REAR PINTLE PINS) (98D32104190001) between the forward and the rear pintles and set it to remove the rear pintle pin.
(4)
Carefully turn the nut of the TOOL - R/I (MLG FWD AND REAR PINTLE PINS) until the rear pintle pin (20) is removed.
R 1EFF : 001-049, 062-099, 101-149, 151-199, 1 32-11-11Page 429 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(5)
Set and install the TOOL - R/I (MLG FWD AND REAR PINTLE PINS) to remove the forward pintle pin (27).
(6)
Carefully turn the nut of the TOOL - R/I (MLG FWD AND REAR PINTLE PINS) until the forward pintle pin (27) is removed.
(7)
Remove the TOOL - R/I (MLG FWD AND REAR PINTLE PINS) from the MLG leg assembly.
(8)
Remove and discard the O-ring (36).
(9)
Put the (CFD1142-00-000) or the (CFD1142-10-000) or the (CFD1142-20-000) in position.
(10) Operate the EQUIPMENT - MLG R/I to lower the MLG leg assembly: (Ref. Fig. 406/TASK 32-11-11-991-008)
(a)
Attach the drive-link between the forward rail assembly (110) and the aft rail assembly (108).
(b)
Turn the drive-link so that the MLG leg assembly moves inboard as far as possible.
(c)
Operate the mini-hoists (113) and (114) and carefully lower the MLG leg assembly onto the .
(11) Safety the MLG leg assembly on the . **ON A/C ALL
Subtask 32-11-11-080-050
F. Removal of the Support Equipment
(Ref. Fig. 406/TASK 32-11-11-991-008)
(1) If the MLG is to be replaced, remove the EQUIPMENT - MLG R/I from the leg assembly:
(a)
Disconnect the lifting cables from the lifting beam (105).
(b)
Remove the lifting beam (105) from the leg assembly.
(c)
Remove the INTERFACE BRACKET (106) from the MLG drag stay.
1EFF : ALL 1 32-11-11Page 430 1 1 Aug 01/05R 1 1 1CES 1
**ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 32-11-11-020-055-A
G. Complete the Removal Procedure WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______ LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the bolts (32).
(2)
Remove the bolts (32) and the seal plate halves (30).
(3)
Remove the sleeve (15) from the rear pintle mounting.
(4) Install the blanking caps to the forward and rear pintles. **ON A/C 301-399,
Subtask 32-11-11-020-055-C
G. Complete the Removal Procedure WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______ LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the bolts (39).
(2)
Remove the bolts (39) and the seal plate halves (37).
(3)
Remove the sleeve (15) from the rear pintle mounting.
(4)
Install the blanking caps to the forward and rear pintles.
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 32-11-11Page 431 1301-399, 1Aug 01/05 1 1 1CES 1
R **ON A/C 001-049, 062-099, 101-149, 151-199, 201-299, 401-499, Post SB 32-1213 For A/C 001-049,101-105,201-203, Subtask 32-11-11-020-055-B
G. Complete the Removal Procedure WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______ LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the bolts (37).
(2)
Remove the bolts (37) and the seal plate halves (35).
(3)
Remove the sleeve (15) from the rear pintle mounting.
(4)
Install the blanking caps to the forward and rear pintles.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(123)
