(2)
Put the doghouse (2) onto the seats tracks (10).
(3)
Pull the lever (8) and move it to the x-direction.
(4)
Turn the lever (8) to the locked position.
(5)
Install the cover (5).
(6)
Install the drawer (2) on the guiderail (3) and lock it with the disconnect knobs (4).
(7)
Push the drawer (2) into the doghouse (1) until it stops and lock it with the latch (11).
**ON A/C 201-210,
Subtask 25-27-46-420-053-A
B. Installation of the doghouse 6600MM and 6601MM R (Ref. Fig. 403/TASK 25-27-46-991-007)
(1)
Apply COMMON GREASE (Material No. 04-004) to the seat track fittings
(4) and the seat tracks (5).
(2)
Install the doghouse:
(a)
Make sure that the lever (2) is in the unlock position.
(b)
Put the doghouse (1) with the fittings (3) in position in the seat tracks (4).
(c)
Move the lever (2) to the locked position.
(3)
Install the drawer:
(a)
Install the drawer (8) on the guide rail (9) and install the screws (5).
(b)
Push the drawer (8) into the doghouse (1) until it stops and the drawer latch (7) engages correctly.
(c)
Lock the drawer lock (6).
(4) Install the cover (10). **ON A/C 151-199, 201-210,
5. Close-up
________ Subtask 25-27-46-410-053
A. Close Access
(1)
Install the seatrow forward of the doghouse (Ref. TASK 25-21-41-400-001).
(2)
Install the equipment in the doghouse, as identified during the removal procedure.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
Make sure that all of the placards of the retained/new components are in the correct position and in a good condition.
(5)
If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001).
Subtask 25-27-46-862-052
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001)
FLOOR PANEL - HEATED, DOOR AREA (5DS,6DS,15DS,16DS) - REMOVAL/INSTALLATION
__________________________________________________________________________
TASK 25-27-51-000-001
Removal of the Heated Floor Panel 5DS (6DS), 15DS (16DS)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific nonmetallic scraper
No specific access platform 3.20 m (10 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power 52-22-00-010-002 Opening of the Emergency Exit Doors from the Outside 25-27-51-991-001 Fig. 401 FOR FIN 5DS, 6DS 25-23-47-000-004 Removal of the Door Frame Linings of the LH FWD
Emergency Exit Door, zone 231 25-23-47-000-009 Removal of the Door Frame Linings of the RH FWD
Emergency Exit Door, zone 232 FOR FIN 15DS, 16DS 53-32-12-000-002 Removal of the Cabin Floor Panels
3. Job Set-up
__________
Subtask 25-27-51-861-050
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 25-27-51-010-050
B. Get Access
(1)
Put the access platform in position adjacent to the emergency exit.
(2)
Open the emergency exit door from the outside (Ref. TASK 52-22-00-010-002).
(3)
FOR 5DS, 6DS
(a) Remove the door frame linings 231GX, 231KX (Ref. TASK 25-23-47-000-004) or 232GX, 232KX (Ref. TASK 25-23-47-000-009) as required.
(4)
FOR 15DS, 16DS
(a) Remove the floor panel 251DG or 252DG as required (Ref. TASK 53-32-12-000-002).
Subtask 25-27-51-865-053
C. Open, safety and tag this(these) circuit breaker(s): -------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(98)
