(b)
Do a visual inspection of the component interface and/or the adjacent area.
(c)
On the installation side of the NTF-covering (1) remove 100 mm (3.9370 in.) protective paper from the self-adhesive film (2).
(d)
Align the NTF (1) with the GFRP (5) and install it with a ROLLER-RUBBER. Move the rubber roller backwards and forwards and around the edges for a better bond.
R EFF : 106-149, 157-199, 210-299, 301-399, 25-28-42Page 435 401-499, Aug 01/05
CES
(e) Do the steps (3)(c) thru (d) until you have installed all of the NTF (1) to the GFRP (5).
(4) Installation of the self-adhesive Film BONDING AND ADHESIVE COMPOUNDS (Material No. 08-082) (2) to the GFRP (5): (Ref. Fig. 401A/TASK 25-28-42-991-001-A)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a)
Clean the component interface and/or the adjacent area.
Use CLEANING AGENTS (Material No. 11-004).
(b)
Do a visual inspection of the component interface and/or the adjacent area.
(c)
Unwind 100 mm (3.9370 in.) of the new self-adhesive film from the roll and remove the protective paper.
(d)
Align the self-adhesive film (2) with the GFRP (5) and install it with a soft cotton cloth and a light pressure of your hand. Work from the middle of the self-adhesive film (2) towards the sides.
(e)
With a ROLLER - RUBBER press down the self-adhesive film (2) onto the GFRP (5).
NOTE : Move the rubber roller backwards and forwards and around
____
the edges for a better bond.
(f) Do the steps (4)(c) thru (e) until you have installed all of the GFRP (5) with the adhesive film (2).
R EFF : 106-149, 157-199, 210-299, 301-399, 25-28-42Page 436 401-499, Aug 01/05
CES Subtask 25-28-42-160-052-A
D. Preparation of the Seat Tracks and the Floor Panels for the Installation of the NTF-Covering. (Ref. Fig. 401A/TASK 25-28-42-991-001-A, 402A/TASK 25-28-42-991-006-A)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Preparation of the Seat Tracks (10):
(a)
Clean the component interface and/or the adjacent area. Use CLEANING AGENTS (Material No. 11-004). If necessary use a vacuum cleaner.
(b)
Do an inspection of the component interface and/or the adjacent area.
(c)
Apply adhesive-promoter SEALANTS (Material No. 09-028B) to the seat track (10).
NOTE : Add to previous step, where the sealant (7) will be
____
applied.
(d) Seal the seat tracks (10): 1 Cut the synthetic fibre-cord MISCELLANEOUS (Material No. 19-
_
002) (8) to the required lenght.
NOTE : The cord must be 50 mm (2 in.) longer than the area
____
that you will seal.
2 Make a loop at one end of each of the cords (8).
_
3 Put the cords (8) in the seat tracks (10).
_ NOTE : This step is to make the next removal procedure easier.
____ 4 Apply SEALANTS (Material No. 09-016) (7) in the seat tracks
_
(10).
R EFF : 106-149, 157-199, 210-299, 301-399, 25-28-42Page 437 401-499, Aug 01/05
CES NOTE : Apply the sealant (7) only, in the area of the adhesive
____ promoter in the seat tracks (10).
5 Push the loops into the sealant (7).
_
(2) Apply corrosion preventive compounds into the seat tracks (10):
(a)
Apply masking paper and masking tape around the seat tracks (10) where you will apply corrosion preventive compounds.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(113)
