F ABS5093B485
MOISTURE BARRIER FOIL,SELF ADHESIVE (Ref. 20-31-00)
USA MIL-PRF-81733D TYPE II CLASS B
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)
ADHESION PROMOTER FOR POLYSULFIDE SEALANT
(Ref. 20-31-00)
SILICONE SEALANT (1 PART) (Ref. 20-31-00)
USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
USA MIL-C-16173 GRADE 3
CORROSION PREVENTIVE COMPOUND (Ref. 20-31-00)
AIB TN 10138 TYPE II GRADE 2
CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
(Ref. 20-31-00)
USA MIL-T-713
SYNTHETIC FIBRE CORD (NYLON) 2.5MM DIA.
(Ref. 20-31-00)
USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 24-41-00-861-002
R
R 24-42-00-862-001
R
R 33-51-12-000-001
R
R 33-51-12-400-001
R
R 25-28-42-991-011
R 25-28-42-991-012
R 25-28-42-991-013
Energize the Aircraft Electrical Circuits from the External Power De-energize the Ground Service Network Supplied from the External Power Removal of the Marking Light of the Floor-Proximity Emergency-Escape Path (LSI) Installation of the Marking Light of the Floor-Proximity Emergency-Escape Path (LSI) Fig. 403 Fig. 404 Fig. 405
EFF : ALL
25-28-42Page 454
May 01/04
3. Job Set-up__________
Subtask 25-28-42-860-053
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized (Ref. TASK 24-41-00-861-002)
(2) Make sure that the NTF area is free from equipment and furnishings.
(3) Make sure that the electrical connectors of the floor path markings are disconnected (Ref. TASK 33-51-12-000-001)
4. Procedure_________
Subtask 25-28-42-160-057
A. Preparation for Installation (Ref. Fig. 403/TASK 25-28-42-991-011, 404/TASK 25-28-42-991-012)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Clean the seat tracks and the NTF-Covering installation area:
R R R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE_______ MADE OF CARBONFIBER REINFORCED PLASTIC.
R
EFF : ALL
25-28-42Page 455
R (a) Clean the seat tracks (10), the component interface and the
R adjacent area with a CLEANING AGENTS (Material No. 11-004), a
R soft cotton cloth MISCELLANEOUS (Material No. 19-003) and a
R SCRAPER - NON METALLIC.
R (b) Make sure that the work area is free from dust and other
R particles. If necessary use a vacuum cleaner.
R (2) Do a visual inspection of the component interface and/or the adjacent
R area.
R (3) Make sure that the parts retained from the removed component are
R clean and in the correct condition.
R (4) Make sure that the lighting in the work area is bright.
R (5) Make sure that the ambient temperature in the work area is between 18
R deg.C (64.40 deg.F) and 30 deg.C (86.00 deg.F).
R (6) Make sure that the ambient humidity in the work area is not more than
R 75 %.
R NOTE : You must monitor the ambient temperature and the ambient____
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(117)
