曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  B. Inspection of the Component 
R  (1) Do a visual inspection of the floor-panels. 
R  (a) Make sure that: 
R  - The floor-panels are in good condition 
R  - The floor-panels are correct installed 
R  - All gaps around the floor-panels are filled with sealant. 
R  (b) If necessary correct the floor-panel installation 
R  Subtask 25-28-41-560-050 
R  C. Textile Floor-Covering Preparation 
R  WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______ 
R  AREA WHEN YOU USE SPECIAL MATERIALS. 
R  IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH 
R  OR IN YOUR EYES : 
R  -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 
R  MINUTES. 
R  -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. 
R  DO NOT BREATHE THE FUMES FROM THE MATERIAL. 
R  DO NOT SMOKE WHEN YOU USE THE MATERIAL. 
R  DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF 
R  HEAT. 
R  THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE 
R  AND SKIN IRRITANTS.

 EFF : ALL
25-28-41Page 406
Feb 01/04

R  NOTE : This work-step is only applicable for installation of textile____ 
R  floor-covering with dispersions-adhesive. 
R  (1) If necessary apply new dispersions-adhesive to the bottom side of the 
R  textile floor-covering (TF): 
R  (a) Make sure that the lighting in the work-room is bright and that 
R  the work-room is free from dust. 
R  (b) Make sure that the ambient room temperature is between 18 deg.C 
R  (64.40 deg.F) and 30 deg.C (86.00 deg.F). 
R  (c) Make sure that the maximum relative room humidity is not more 
R  than 75%. 
R  NOTE : You must monitor the ambient room temperature and the____ 
R  ambient humidity of the work-room with suitable 
R  instruments. 
R  (d) Make sure that the textile floor-covering (7) is clean and in the 
R  correct condition. 
R  WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ 
R  THIS/THESE MATERIAL/S. 
R  USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A 
R  MASK. 
R  (e) Apply 120 g (4.23 oz) (fluid weight) of BONDING AND ADHESIVE 
R  COMPOUNDS (Material No. 08-102) per 1 m2 (10.76 ft.2) with an 
R  application device to the bottom side of the textile 
R  floor-covering (7). 
R  NOTE : You must apply (fluid weight) 150 g (5.29 oz) of BONDING____ 
R  AND ADHESIVE COMPOUNDS (Material No. 08-102) per 1 m2 
R  (10.76 ft.2) when you install heavy textile floor-covering 
R  (7) with a rough bottom-structure. 
R  (f) Move the application-device cross-wise over the surface to make 
R  sure that you apply the dispersion-adhesive equally to the 
R  textile floor-covering (7). 
R  (g) Let the dispersion-adhesive layer become stable and dry for a 
R  minimum of 16 h: 
R  - at a room temperature between 18 deg.C (64.40 deg.F) and 30 
R  deg.C (86.00 deg.F) 
R  - at a maximum relative room humidity of 75%.

 EFF : ALL
25-28-41Page 407

R  Subtask 25-28-41-560-051 
R  D. Seat-Track Preparation 
R  (1) Seat-tracks areas which stay free from seats or seat-track covers 
R  must be filled with a section (Detail C). 
R  (2) Installation of the section: 
R  (a) Cut the Section (4) in the required length. 
R  (b) Put the section (4) into the seat-track (3). 
R  Subtask 25-28-41-560-052 
R  E. Installation of the Adhesive Tapes onto the floor panels 
R  (1) Make sure that the lighting in the work area is bright. 
R  (2) Make sure that the ambient temperature in the work area is between 18 
R  deg.C (64.40 deg.F) and 30 deg.C (86.00 deg.F). 
R  (3) Make sure that the ambient humidity in the work area is not more than 
R  75 %. 
R  NOTE : You must monitor the ambient temperature and the ambient____ 
R  humidity of the work area with suitable instruments. 
R  (4) Installation of the floor-panel protection-tape: 
R  (a) Unwind the protection-tape (2) BONDING AND ADHESIVE COMPOUNDS 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(104)