(5)
 Remove the flouresent tubes(Ref. TASK 33-21-11-000-001).

 (6)
 Remove the emergency oxygen container (Ref. TASK 35-21-41-000-001).

 EFF : ALL

25-24-41Page 402

 Subtask 25-24-41-010-051
 D. Remove the Passenger Service Equipment.
 (1) Remove the passenger service/information unit (Ref. TASK 25-25-11-000-001).
 (2) Remove the passenger reading light-panel (Ref. TASK 21-24-19-000-001).
 (3) Remove the individual air-outlet panel (Ref. TASK 21-24-19-000-001).
 4. Procedure_________
 Subtask 25-24-41-020-050
 A. Removal of the 2,3 and 4-frame stowage compartments. (Ref. Fig. 401/TASK 25-24-41-991-001)
 (1) Remove the lower attachments. 
R R  (a) Disengage the panel (2) from the attachment rail (1), pull it down and remove it.
 (b) Remove the screw (46), the washer (47), the nut (48) and disconnect the bonding strap (6).
 (c) If necessary remove the clamps (3) and disconnect the hoses (4).
 (d) Remove the nuts (32), the washers (31), (30) and the screws (29). 
R R  (e) Remove the lock-pins (20), the washers (19) and the pins (18) and (21).
 (f) Remove the nuts (40), the washers (38), (39), (43) and the screws (37), (41) and (42).
 (2) Remove the upper attachments.
 (a) Open the stowage compartment doors (5) for access.
 (b) Remove the split-rings (9), the washers (8) (Ref. Detail "A" and "B").
 (c) Remove the nuts (27) the washers (25) and (26) (Ref. Detail "H"and "J").

 EFF : ALL

25-24-41Page 403

R R  2, 3 and 4-Frame Stowage Compartments Figure 401/TASK 25-24-41-991-001- 12 (SHEET 1)
 EFF :  ALL  25-24-41 Page 404 Aug 01/02
 CES 

R R  2, 3 and 4-Frame Stowage Compartments Figure 401/TASK 25-24-41-991-001- 22 (SHEET 2)
 EFF :  ALL  25-24-41 Page 405 Aug 01/02
 CES 

 (d)
 Record the position and the number of the washers (28) for the installation procedure.

 (e)
 Support the stowage compartment and remove the pins (7) and (10) (Ref. Detail "A" and "B") or remove the screws (24), (36) and the washers (25), (26) and (28) (Ref. Detail "H" and "J")

 (f)
 Remove the stowage compartment. NOTE : The cabin temperature sensor casing (3) is installed

____ between two overhead stowage compartments (1) and (2). If you must remove one or both of these overhead stowage compartments (1) and/or (2), do these steps:
 (Ref. Fig. 402/TASK 25-24-41-991-005)
 (g)
 Loosen the clamp (5).

 (h)
 Remove the hose (6) from the cabin temperature sensor (4) outlet pipe.

R (i) Remove the screws (7), and remove the screen (8) from between the R overhead stowage compartments (1) and (2).
 NOTE : The cabin temperature sensor casing (3) stays attached to
____ its overhead stowage compartment (2).
 Subtask 25-24-41-020-051
 B. Removal of the 1-frame stowage compartments/spacer bins.
 (Ref. Fig. 403/TASK 25-24-41-991-012)

 (1)
 Remove the nuts (54), the washers (53), (52) and the screws (51).

 (2)
 Remove the pin-locks (20), the washers (19) and the pins (18).

 (3)
 Remove the nut (48), the washer (47), the screw (46) and disconnect the bonding strap (6).

 (4)
 Remove the screws (44) and the washers (45).

 (5)
 Remove the split-ring (9) and the washer (8) (Ref. Detail "B").

 (6)
 Remove the nuts (27) and the washers (25) and (26) (Ref. Detail "A" and "G").

 EFF : ALL

25-24-41Page 406

 Cabin Temperature Sensor Casing - Removal/Installation Figure 402/TASK 25-24-41-991-005
R  EFF : CES  ALL  25-24-41 Page 407 Aug 01/02 

R R  1-Frame Stowage Compartments/Spacer Bins Figure 403/TASK 25-24-41-991-012
 EFF :  ALL  25-24-41 Page 408 Aug 01/02
 CES 

 (7)
 Record the position and the number of the washers (28) for the installation procedure.

 (8)
 Support the stowage/spacer bin and remove the pin (7) (Ref. Detail "B") and/or the bolts (24), (36) and the washers (25), (26) and (28) (Ref. Detail "A" and "G").

 (9) Remove the stowage/spacer bin. Subtask 25-24-41-020-052
 C. Removal of the spacer bin FR38/ FR39.
 (Ref. Fig. 404/TASK 25-24-41-991-013)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(59)