A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the stowage is empty.
4. Procedure
_________
Subtask 25-27-44-210-070
A. Preparation for Installation
(1) Clean the seat tracks:
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Clean the seat tracks with CLEANING AGENTS (Material No. 11-003) a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and a SCRAPER - NON METALLIC.
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
**ON A/C 001-049, 101-105,
Subtask 25-27-44-420-058-A
B. Installation of the Stowage 6575MM
WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R (Ref. Fig. 401/TASK 25-27-44-991-001-A)
R (1) Unless specified, TORQUE all nuts, bolts and screws (Ref. TASK 20-21-11-911-001).
R R (2) Apply COMMON GREASE (Material No. 04-004) to the seat-track fittings (7) and the stoppers (6), and put them in the seat tracks (8) as recorded in the removal procedure.
R (3) Seal the seat tracks:
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R R (a) Cut the synthetic fiber-cords (9) MISCELLANEOUS (Material No. 19-002) to the necessary length.
NOTE : The cords (9) must be 50 mm (2 in.) longer than the area____ that you will seal.
(b) Put the cords (9) in the seat tracks (8).
(c) Make a loop at one end of each of the cords (9).
NOTE : This step is to make the next removal procedure easier.____
R R (d) Apply SEALANTS (Material No. 09-019) to the seat tracks (8) for a length of 30 mm (1.2 in.).
(e) Push the loops into the sealant.
R (4) Carefully put the stowage (1) in position.
R (5) Put the washers (5) in position and install the nuts (4).
CES
R (6) Put the covers (2) in position and install the screws (3). R (7) Make sure that all of the placards of the retained/new components are in the correct position and in good condition. R (8) If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001). **ON A/C 151-199,
Subtask 25-27-44-420-058
B. Installation of the Stowage 6579MM WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
(Ref. Fig. 401A/TASK 25-27-44-991-001)
(1)
Unless specified, TORQUE all nuts, bolts and screws (Ref. TASK 20-21-11-911-001).
(2)
Apply COMMON GREASE (Material No. 04-004) to the seat-track fittings
(11) and (19), and the stoppers (10) and (18), and put them in the seat tracks (12) as recorded in the removal procedure.
(3)
Seal the seat tracks: WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Cut the synthetic fiber-cords (13) MISCELLANEOUS (Material No. 19-002) to the required length.
NOTE : The cords (13) must be 50 mm (2 in.) longer than the area
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(89)
