_________ Subtask 25-26-43-020-061
A. Remove the Center Class Divider Rail System.
(Ref. Fig. 405/TASK 25-26-43-991-014)
(1) Remove the center class divider rail (refer to as rail):
(a)
Open the door (9) of the overhead stowage compartment.
(b)
Hold the rail (1) in position and remove the screws (7) and the washers (6).
(c)
Carefully remove the rail (1) and the shim plates (5).
(d)
Remove the sleeves (2),the springs (4),the pins (3) and the spacers (8).
R EFF : 001-049, 051-052, 101-105, 151-199, 25-26-43Page 424 301-399, May 01/05
CES
MCD-Center Rail Figure 405/TASK 25-26-43-991-014
R EFF : 001-049, 051-052, 101-105, 151-199, 301-399, 25-26-43 Page 425 May 01/05
CES
TASK 25-26-43-400-012 Installation of the MCD Rail System
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power 25-26-43-400-004 Installation of the Center Class Divider 25-26-43-991-014 Fig. 405
3. Job Set-up
__________ Subtask 25-26-43-860-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized
(Ref. TASK 24-42-00-861-001)
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
R EFF : 001-049, 051-052, 101-105, 151-199, 25-26-43Page 426 301-399, May 01/05
CES 4. Procedure
_________
Subtask 25-26-43-420-059
A. Installation of the Center Class Divider Rail System:
(Ref. Fig. 405/TASK 25-26-43-991-014)
(1) Install the center class divider rail (refer to as rail).
(a)
Make sure that the door (9) of the overhead stowage compartment is open.
(b)
Put the rail (1) and the washers (6) in position and install the screws (7), but do not tighten.
(c)
Install the sleevers (2), the springs (4) and the pins (3).
(d)
Align the rail system, if necessary install shim plates (5) and spacers (8).
(e)
Tighten the screws (7).
5. Close-up
________
**ON A/C 301-399,
Subtask 25-26-43-410-064
A. Close Access
(1) Install the center class divider (Ref. TASK 25-26-43-400-004). R **ON A/C 001-049, 051-052, 101-105, 151-199, 301-399,
Subtask 25-26-43-862-055
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001)
ANCILLARY EQUIPMENT (INCLUDING DOOR AREA HEATING PANELS)
________________________________________________________ DESCRIPTION AND OPERATION
_________________________
1. General
_______
A. Stowages
There are different stowage devices for the ancillary equipment.
The stowage devices are installed at different locations in the cabin.
**ON A/C 301-399,
B. Door Area Heating System The heated floor panels increase the temperature of the floor in some areas to give more comfort to the crew and the passengers.
**ON A/C ALL
2. Component Location
__________________
R **ON A/C 001-049, 101-105,
A. Stowages (Ref. Fig. 001) -------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA
| | | | DOOR | REF. -------------------------------------------------------------------------------6575MM STOWAGE LH 231 25-27-44 6576MM STOWAGE RH 232 25-27-44 ------EMERGENCY EQUIPMENT STOWAGE 261 25-27-15
R **ON A/C 051-099,
R A. Stowages R (Ref. Fig. 001A) R -------------------------------------------------------------------------------R FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA R | | | | DOOR | REF. R -------------------------------------------------------------------------------R ------EMERGENCY EQUIPMENT STOWAGE 261 25-27-15
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設(shè)備2(80)
