(b)
Remove the screws (2).
(c)
Remove the screws (10) and the cover plate (9).
(d)
Turn the pins (8) out and lower them together with the upper attachment tubes (7).
(e)
Carefully lift the partition (1) until it is free of the seat track fittings (4) and remove it.
(f)
Record the quantity and the location of the shim plates (3).
(g)
Remove the shim plates (3).
(h)
Record the position of the seat track fittings (4) for the installation procedure.
(i) Remove the seat track fittings (4) from the seat tracks.
**ON A/C 201-210,
Subtask 25-26-42-020-056
A. Removal of the Partitions: NOTE : The procedure of the left and right Partition is the same.
____
(1)
Lift the carpet as far as necessary to get access to the screws (6).
(2)
Remove the screws (6).
(3)
Remove the partition (1).
(a)
Hold the partitions (1) in position.
(b)
Move the release pin (5) in the release hole, turn it 90 degrease clockwise or counterclockwise.
(c)
Pull the support tubes (2) down to release it from the upper support (3).
(d)
Lift the partition (1) until it is free of the lower supports (8) and remove it.
(4)
Remove the stoppers (7) and the lower supports (8) from the seat tracks (9).
(5)
Pull the synthetic fiber cord and remove the sealant from the seat tracks (9).
(6)
Clean the seat tracks (9).
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Clean the seat tracks (9) with CLEANING AGENTS (Material No. 11-003) a nonmetallic scraper and a cloth MISCELLANEOUS (Material No. 19-003) **ON A/C 301-399,
Subtask 25-26-42-020-056-B
A. Removal of the Partition. WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY. (Ref. Fig. 401B/TASK 25-26-42-991-005-B) NOTE : The procedure for the left and/or right partition is the same.
____
(1) Remove the partition:
(a)
Remove the covers (8).
(b)
Remove the screws (4) and the washers (5).
(c)
Lift the partition (1) until it is free of the seat track fittings (7) and the stoppers (6).
(d)
Remove the partition (1) with the tubes (3) out of the upper attachment panel (2).
(e)
Record the position of the seat track fittings (7) for the installation procedure.
(f)
Remove the stoppers (6) and the seat track fittings (7) from the seat tracks.
EFF : 301-399, 25-26-42Page 409
May 01/05
R
CES
R **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
TASK 25-26-42-400-005
Installation of a Class Divider Partition (Zone 230)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific release pin
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 08-065 USA MIL-T-60394 TYPE I CLASS I 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(73)
