(b)
 Put the connector (10) (if removed) in position in the support assembly (2) and install the screws (9), the washers (11) and the nuts (12).

 (c)
 Install the support assembly (2) in the class divider (3).

 (d)
 Install the screws (1).

 (e)
 Install the grip plate (4).

 (f)
 Put the grips (5) in position and install the screws (6).

 Lateral Divider - Assembly Figure 402/TASK 25-26-43-991-011 
R  EFF :  001-049, 101-105,  25-26-43 Page 406 May 01/05
 CES 

 (g) Put the cover (7) in position and install the screws (8). Subtask 25-26-43-420-052
 B. Install the Lateral Class Divider. NOTE : The procedure for the left and right lateral divider is the same.
____
 (1)
 Remove the cover (5) from the attachment panel (2).

 (2)
 Put the class divider (1) in position.

 (3)
 Make sure the electrical connector (8) is in the correct position (if installed).

 (4)
 Make sure the guide pins (7) engage correctly.

 (5)
 Push the class divider (1) up until the self-lock mechanism locks in position.

 Subtask 25-26-43-861-063
 C. Energize the CIDS (Ref. TASK 23-73-00-861-001). Subtask 25-26-43-861-050
 D. Energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-861-002) .

 Subtask 25-26-43-710-050
 E. Do the operational test of the passenger information signs.
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the panel 25VU:  On the left and right class dividers:
 -set the SEAT BELTS switch to  - the FASTEN SEAT BELTS sign comes on. the ON position.
 2. On the panel 25VU:  On the left and right class dividers:
 -set the NO SMOKING switch to  - the NO SMOKING sign comes on.
 the ON position.

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
3. Set the SEAT BELTS switch and the NO SMOKING switch on panel 25VU to the OFF position.
 5. Close-up
________
 Subtask 25-26-43-862-050
 A. De-energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-862-002).

R  **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
 TASK 25-26-43-000-004
 Removal of the Center Class Divider
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 25-26-41-000-013 Removal of the Curtains
R  **ON A/C 001-049, 101-105, 151-199,
 25-26-43-991-004-A Fig. 403
 **ON A/C 201-210,
 25-26-43-991-004 Fig. 403A
 **ON A/C 301-399,
 25-26-43-991-004-B Fig. 403B R **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
 3. Job Set-up
__________
 Subtask 25-26-43-861-055

 A. Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

R  EFF : 001-049, 101-105, 151-199, 201-210, 25-26-43Page 409 301-399, May 01/05
 CES  Subtask 25-26-43-010-066

 B. Get Access
 (1)
 Remove the curtain from the center class divider (Ref. TASK 25-26-41-000-013).

 (2)
 Make sure that the Overhead Stowage Doors are closed.

 4. Procedure
_________ R **ON A/C 001-049, 101-105, 151-199,
 Subtask 25-26-43-020-053-A
 A. Remove the Center Class Divider 6388MM.
 (Ref. Fig. 403/TASK 25-26-43-991-004-A)

 (1)
 Remove the screws (4) the washers (5) and the stoppers (6) from the divider rail (7).

 (2)
 Push the triggers (2) and pull the class divider (1) by the handles

 (3) down.

 (3)
 Move the class divider (1) forward until frame 24, move it out of the rail (7) and remove it.

 **ON A/C 201-210, 301-399,
 Subtask 25-26-43-020-053
 A. Remove the Center Class Divider.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(77)