曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Figure 401 (Sheet 5 of 5)/27-62-12-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-12
Page 407
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-62-12-400-801
3. Inboard Ground Spoiler Installation
(Figure 401)
A. References
Reference Title
27-62-00-800-801 Speed Brake Hydraulic Systems A and B Pressurization (P/B 201)
27-62-00-820-804 Ground Spoiler Adjustment (P/B 501)
27-62-00-840-801 Put the Speed Brake Hydraulic systems A and B Back to the
Condition Before the Pressurization (P/B 201)
27-62-00-840-802 Put the Speed Brake Systems A and B Back to the Condition Before
the Pressure Removal (P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1744 Set - Lock, Inboard Ground Spoiler Actuator (Contains 4 Lock
Assemblies)
(Part #: C27046-13, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
(Opt Part #: C27046-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Consumable Materials
Reference Description Specification
D00633 Grease - Aircraft General Purpose BMS3-33
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
1 Inboard Ground Spoiler 27-62-71-01-005 GUN ALL
57-42-00-04-005 GUN 001-014, 101-108,
111, 115, 155-157, 201-
999
5 Pin 27-31-34-04-057 GUN 156, 201-204, 206
57-42-00-04-010 GUN 008-099, 101-122
16 Pin 27-62-71-01-195 GUN ALL
19 Pin 57-42-00-04-055 GUN 008-099, 101-122
30 Pin 57-42-00-04-055 GUN 008-099, 101-122
33 Pin 27-62-71-01-195 GUN ALL
44 Pin 27-31-34-04-057 GUN 156, 201-204, 206
57-42-00-04-010 GUN 008-099, 101-122
E. Location Zones
Zone Area
210 Subzone - Control Compartment - Body Station 178.00 to Body
Station 259.50
552 Left Wing - Spoiler No. 6
652 Right Wing - Spoiler No. 7
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-12
Page 408
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
F. Inboard Ground Spoiler Installation
SUBTASK 27-62-12-420-001
(1) Install the Inboard Ground Spoiler [1]:
(a) Put the Inboard Ground Spoiler [1] in its position on the airplane.
(b) Install the bolt [41] with the head inboard, washer [40], bushing [39], washer [42], nut [43],
and pin [44] in the inboard hinge fitting.
(c) Install the bolt [25] with the head outboard, washer [26], bushing [27], washer [28], nut [29],
and pin [30] in the center right hinge fitting.
(d) Install the bolt [23] with the head outboard, washer [22], bushing [21], washer [20], nut [18],
and pin [19] in the center left hinge fitting.
(e) Install the bolt [2] with the head outboard, washer [3], bushing [4], washer [7], nut [6], and
pin [5] in the outboard hinge fitting.
(f) Install washer [8], washer [9] and nut [11] and connect the bonding jumper [10] to the
Inboard Ground Spoiler [1].
NOTE: Bend the bonding jumper 45 +/- 5 degrees away from the fitting.
(g) Install washer [46] washer [48] and nut [47] and connect the bonding jumper [45] to the
Inboard Ground Spoiler [1].
NOTE: Bend the bonding jumper 45 +/- 5 degrees away from the fitting.
SUBTASK 27-62-12-980-001
(2) Move the Inboard Ground Spoiler [1] through its full travel.
(a) Make sure the Inboard Ground Spoiler [1] moves freely.
SUBTASK 27-62-12-420-002
(3) Install the bolt [12] that attaches the rod end of the outboard actuator [24] to the Inboard Ground
Spoiler [1]:
(a) Apply a layer of grease, D00633 to the bolt [12].
(b) Install the bolt [12] with its head outboard.
(c) Install the washer [13], bushing [14], washer [15], and nut [17], and on the bolt [12].
(d) Tighten the nut [17].
(e) Install the pin [16].
(f) Apply grease, D00633 to the bolt [12], washer [13], bushing [14], washer [15], nut [17], and
pin [16].
SUBTASK 27-62-12-420-003
(4) Install the bolt [37] that attaches the rod end of the inboard actuator [38] to the Inboard Ground
Spoiler [1]:
(a) Apply a layer of grease, D00633 to the bolt [37].
(b) Install the bolt [37] with its head outboard.
(c) Install the washer [36], bushing [35], washer [34], nut [32], nut [31] and pin [33] on the bolt
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(81)