曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-61-00-860-115
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER,
ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) Do this task: Hydraulic System A or B Pressurization, TASK 29-11-00-860-801.
SUBTASK 27-61-00-860-116
(3) Move the speed brake lever to the full DOWN position.
SUBTASK 27-61-00-860-117
(4) Move the captain’s aileron control wheel to the neutral position.
D. Alternate Spoiler Position Sensor Test
SUBTASK 27-61-00-740-001
(1) Do this BITE test on the control display unit (CDU):
NOTE: Only spoilers 4 and 9 can be tested using the BITE. Spoiler position sensors 3 and 10
cannot be tested using the BITE.
(a) Push the INIT REF key on the CDU keyboard.
(b) Push the Line Select Key (LSK) that is adjacent to these selections:
NOTE: Use the NEXT PAGE or PREV PAGE key to change page if it is necessary. During
the BITE test, if the "CONTINUE" shows, then push the LSK that is adjacent to
"CONTINUE" after you do the instructions that show on the CDU display.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 556
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) INDEX
2) MAINT
3) DFCS
4) EXTENDED MAINTENANCE
5) RIGGING
6) AILERON
7) CONTINUE
(c) Do the instructions that show on the CDU and push the LSK adjacent to these selections:
1) CONTINUE
2) Select SPOILER
3) CONTINUE
SUBTASK 27-61-00-740-002
(2) The CDU will display a screen showing UL, LL, A and B values for spoiler number 4 (speedbrake
lever in the FULL DOWN position). Do the following:
(a) Make sure that the A and B values are within the UL and LL limits.
(b) Record the values of A and B for spoiler 4.
1) Select CONTINUE
SUBTASK 27-61-00-740-003
(3) The CDU will display a screen showing UL, LL, A and B values for spoiler number 9 (speed
brake lever in the FULL DOWN position). Do the following:
(a) Make sure that the A and B values are within the UL and LL limits.
(b) Record the values of A and B for spoiler 9.
1) Select CONTINUE
SUBTASK 27-61-00-700-021
(4) Move the speed brake lever to the FLIGHT DETENT position.
(a) Select CONTINUE
SUBTASK 27-61-00-700-022
(5) The CDU will display a screen showing UL, LL, A and B values for spoiler number 4 (speed
brake lever in the FLIGHT DETENT position). Do the following:
(a) Make sure that the A and B values are within the UL and LL limits.
(b) Record the values of A and B for spoiler 4.
1) Select CONTINUE
SUBTASK 27-61-00-740-004
(6) The CDU will display a screen showing UL, LL, A and B values for spoiler number 9 (speed
brake lever in the FLIGHT DETENT position). Do the following:
(a) Make sure that the A and B values are within the UL and LL limits.
(b) Record the values of A and B for spoiler 9.
1) Select CONTINUE
SUBTASK 27-61-00-740-008
(7) Push the INIT/REF key to exit the BITE.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 557
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
E. Put the Airplane Back to Its Usual Condition
SUBTASK 27-61-00-860-118
(1) Move the speed brake lever to the DOWN detent.
SUBTASK 27-61-00-860-119
(2) Do this task: Hydraulic System A or B Pressurization, TASK 29-11-00-860-801.
SUBTASK 27-61-00-860-120
(3) Do this task: Remove Electrical Power, TASK 24-22-00-860-812.
------------------------- END OF TASK ---------------------------
TASK 27-61-00-820-809
14. Spoiler Mixer No-Back Assembly Test
(Figure 505)
A. References
Reference Title
27-61-21-000-801 Spoiler Mixer Removal (P/B 401)
27-61-21-400-801 Spoiler Mixer Installation (P/B 401)
27-61-31-400-801 Spoiler Ratio Changer Installation (P/B 401)
27-62-00-820-802 Speed Brake Control Cable Adjustment (P/B 501)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(22)