曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

EFFECTIVITY
GUN ALL 27-61-00
Page 547
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Table 505/27-61-00-993-820
Spoiler Position Required Position Actual Position
Spoilers 2, 3 4 and 5 are starting to
move down.
Control wheel should be at 65
degrees minimum
Control Wheel was at
______________ degrees
Spoilers 2, 3 4 and 5 are fully down. Control wheel should be at 5 +/- 3
degrees
Control Wheel was at
______________ degrees
SUBTASK 27-61-00-480-018
(5) Do the steps below in turn for spoiler panels 8, 9, 10 and 11.
(a) Install the protractor, COM-1691 on the spoiler panel.
1) Note the location of the protractor.
2) Adjust the protractor, COM-1691 to zero.
(b) Turn the control wheel clockwise to 30 degrees and hold.
1) Using the spoiler protractor, note the position of spoiler panel.
NOTE: If you have to remove the protractor to measure the angle of the spoiler panel,
make sure you replace it in the same location from where it came.
(c) Continue to turn the control wheel clockwise to the 87 degree wheel position.
1) Using the spoiler protractor, note the new position of the spoiler panel.
2) Verify the left wing spoilers are in the down position.
(d) Make sure the right wing flight spoiler panels 8, 9, 10 and 11 stay in the full down position.
(e) Shake-out and center the control wheel.
SUBTASK 27-61-00-020-018
(6) Make sure that the noted position of the spoiler panel is within the spoiler position limits as are
shown in the table.
SUBTASK 27-61-00-020-019
(7) Make sure that the noted position of the spoiler panel is within the spoiler position limits as are
shown in the table.
SUBTASK 27-61-00-860-101
(8) Do the following steps:
(a) Turn the control wheel to 87 degrees in the clockwise direction.
(b) Slowly turn the control wheel in the counterclockwise direction.
(c) Stop turning the control wheel when spoiler panels 8, 9, 10 and 11 start to move down.
1) Record the control wheel position.
(d) Slowly begin turning the control wheel to the neutral position.
(e) Stop turning the control wheel when spoiler panels 8 and 9 reach the full down position.
NOTE: In the FULL DOWN position it is normal for spoiler panel 8 to be slightly higher
than spoiler panel 9.
1) Record the control wheel position.
(f) Make sure the noted control wheel positions are within the limits shown in the table below.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 548
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Table 506/27-61-00-993-822
Spoiler Position Required Position Actual Position
Spoilers 8, 9 10 and 11 are starting
to move down.
Control wheel should be at 65
degrees minimum
Control Wheel was at
______________ degrees
Spoilers 8, 9 10 and 11 are fully
down.
Control wheel should be at 5 +/- 3
degrees
Control Wheel was at
______________ degrees
SUBTASK 27-61-00-860-102
(9) Shake-out and center the control wheel.
SUBTASK 27-61-00-860-103
(10) Do the following steps to test spoiler panel response at the ’ARMED’ detent position.
(a) Move the speed brake lever from DOWN to FULL UP at least six times.
(b) Move the speedbrake lever to the down and locked position.
(c) Move the speed brake lever to the ’ARMED’ detent position.
(d) Make sure that flight spoilers 2, 3, 4, 5, 8, 9, 10 and 11 are not extended more than 1.50
degrees (0.63 inch) at the trailing edge.
NOTE: Make sure to zero the protractor on each panel in the down position prior to
measuring panel angle.
(e) Move the speed brake to the DOWN and LOCKED position.
SUBTASK 27-61-00-860-104
(11) Do the following steps to test spoiler equalization with partial Speed Brake (Table 507).
NOTE: These steps must be carried out separately for corresponding spoiler panels 2 and 11,
3 and 10, 4 and 9 and 5 and 8.
(a) Adjust the spoiler panel protractor to read zero degrees on the left wing spoiler panel in the
DOWN position
(b) Note the location of the protractor on the spoiler panel.
(c) Move the speed brake lever from the down and locked position until the left wing spoiler
panel is raised 15 +/- 1 degrees.
(d) Using the protractor, measure the position of the left wing spoiler panel.
(e) Return the protractor to the location noted on the spoiler panel.
(f) Measure and record the position of the right wing spoiler panel.
NOTE: Do NOT adjust the protractor zero for this measurement.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(18)