曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN
YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
5) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
6) Move the speedbrake lever to the DOWN position.
7) Check the clearance at the trailing edge of the ground spoilers.
a) Make sure the clearance is within the limits (Figure 506).
8) If the clearance of the ground spoiler is not in the limits, do the following to adjust the
actuator:
a) Do this task: Extend the Trailing Edge Flaps, TASK 27-51-00-860-803.
b) Do this task: Remove Pressure from the Speed Brake Hydraulic Systems A and
B, TASK 27-62-00-800-802.
c) Adjust the spoiler actuator again, as necessary.
9) If the clearance of the ground spoiler is in the limits, do the following:
a) Do this task: Extend the Trailing Edge Flaps, TASK 27-51-00-860-803.
b) Move the speed brake lever to the UP position to extend the spoilers.
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER.
AILERONS, RUDDERS, ELEVATORS, FLAPS, SLATS, SPOILERS,
LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN
YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
c) Do this task: Remove Pressure from the Speed Brake Hydraulic Systems A and
B, TASK 27-62-00-800-802.
d) Clean all grease from the piston rod and the rod end threads with Series 84 solvent,
B01004 (TASK 20-30-84-910-801).
e) Apply a layer of the corrosion preventive compound to the threads of the piston rod
end.
f) Install the locking key in the actuator rod end.
g) Torque the checknut to 600 - 720 pound-inches (67.80 - 81.36 newton-meters).
h) Install the lockwire, G01912 on the checknut.
i) Apply a bead of sealant, A00247 to the rod end checknut.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 536
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
F. Put the Airplane Back to Its Usual Condition
SUBTASK 27-62-00-860-223
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS,
ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
SUBTASK 27-62-00-860-030
(2) Move the speed brake lever to the DOWN position to lower the spoilers if it is necessary.
SUBTASK 27-62-00-860-031
(3) Do this task: Retract the Trailing Edge Flaps, TASK 27-51-00-860-804.
SUBTASK 27-62-00-860-033
(4) Do this task: Put the Speed Brake Systems A and B Back to the Condition Before the
Pressure Removal, TASK 27-62-00-840-802.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 537
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Ground Spoiler Adjustment
Figure 506 (Sheet 1 of 3)/27-62-00-990-807
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 538
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Ground Spoiler Adjustment
Figure 506 (Sheet 2 of 3)/27-62-00-990-807
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 539
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Ground Spoiler Adjustment
Figure 506 (Sheet 3 of 3)/27-62-00-990-807
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 540
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-62-00-800-803
9. Speed Brake Lever Friction Test
A. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
27-62-00-800-801 Speed Brake Hydraulic Systems A and B Pressurization (P/B 201)
27-62-00-840-801 Put the Speed Brake Hydraulic systems A and B Back to the
Condition Before the Pressurization (P/B 201)
FIM 27-62 TASK 807 Speed Brake Lever Does Not Move Freely - Fault Isolation
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(67)