曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The compass card on the KI 227 may
be rotated as desired by using the
heading knob.
NOTE: The KI 227-01 or KI 228-01 indicators,
when installed with a Bendix/King
KCS 55A Compass System, have a
slaved compass card. Magnetic heading
of the aircraft will be under the lubber line.
The indication of this compass card
should be compared with that of the
KI 525A master indicator from time to
time. Check especially after steep
bank turns and taxi turns. If a discrepancy
between the two readings exists,
the KI 227-01 or KI 228-01 compass
card should be synchronized to the
KI 525A compass card by rotating the
“SYNC” knob on the indicator.
Outside of the United States some
stations are unmodulated and use an
interrupted carrier for identification purposes.
The BFO mode, activated and
annunciated when the “BFO” button is
depressed, permits the carrier wave
and the associated Morse code identifier
broadcast on the carrier wave to be
heard.
ADF Test
(PRE-FLIGHT OR IN-FLIGHT)
Select ANT mode. This will cause
the bearing pointer to move directly to
231 39:38
323 2 31
323 2 31
29
KR 87
the parked 90° position. Make sure the
unit is tuned to a usable frequency.
Now select ADF mode and the needle
should move without hesitation to the
station bearing. Excessive sluggishness,
wavering or reversals indicate a
signal that is too weak or a system malfunction.
Operating the Timers
The flight timer will always be automatically
reset to :00 whenever power
is interrupted either by the avionics
master switch or the unit’s ON/OFF
switch. An optional external switch may
be installed which, when activated, will
stop or start the flight timer. This switch
would be of use during a non-refueling
stop when resetting the flight timer is
not desired. On some aircraft it may be
desirable to use the aircraft strut switch
instead of a manual switch to stop and
start the flight timer. It should be
emphasized that the start/stop function
will only operate with power applied to
the unit. Always read flight time prior to
power shutdown.
Flight time or elapsed time are displayed
and annunciated alternatively by
depressing the FLT/ET button. The
flight timer continues to count up until
the unit is turned off or stopped with an
external switch. The elapsed timer may
be reset back to :00 by pressing the
SET/RST button. It will then start
counting up again. (NOTE: pressing
the SET/RST button will reset the
elapsed timer whether it is being displayed
or not.)
The elapsed timer also has a
“count-down” mode. To enter the
countdown mode, the SET/RST button
is depressed for about two seconds, or
until the “ET” annunciation begins to
flash. It is now in the ET set mode, and
a time up to 59 minutes, 59 seconds
may be preset into the elapsed timer
with the concentric knobs. The preset
time will be displayed and remain
unchanged until SET/RST is pressed
again, which will start the elapsed timer
counting down from the preset time.
When the timer reaches :00 it will start
to count up as the display flashes for
15 seconds and an aural alarm, if
installed, is activated for about 1 second.
NOTE: The standby frequency which is
in memory while flight time or elapsed
time modes are being displayed may be
called back by pressing the FRQ button,
then transferred to active use by pressing
the FRQ button again.
While FLT or ET is displayed the “in
use” frequency on the left side of the
window may be changed, by using the
frequency select knobs, without any
effect on the stored standby frequency
or the other modes. This feature is
especially useful when searching for
stations with unknown frequencies.
Erroneous ADF Bearings Due
to Radio Frequency
Phenomena
Station Overlap
In the U.S., the FCC, which assigns
AM radio frequencies, occasionally will
assign the same frequency to more than
one station in an area. Certain conditions,
such as Night Effect, may cause
signals from such stations to overlap.
This should be taken into consideration
when using AM broadcast stations for
navigation.
Sunspots and atmospheric phenomena
may occasionally distort reception
so that signals from two stations on the
same frequency will overlap. For this
reason it is always wise to make positive
identification of the station being tuned,
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：RMIT Flight Training RMIT飛行訓練(57)