S 864-003

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6-2 Main Power Distribution Panel
 1) 6K18, APU ALTN CONT

 (b)  
P83 Aft APU Equipment Control and Circuit Breaker Panel 1) APU PRIME CONT

 S 014-027
 (3)  
Open the left APU access door, 317AL, and right APU access door, 318AR:

 (a)  
While you hold the two APU access doors in the closed position, open the six latches on the right access door.

 NOTE: The left access door will open fully and the right
____ access door will drop approximately one inch (2.5 cm) from the fuselage frame when the last latch is opened.
 NOTE: A lanyard is attached to the aft end of the right access
____ door to hold the access door to the APU compartment bulkhead.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-07

 ALL  ú ú 01 Page 401 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 CAUTION: BE CAREFUL NOT TO MOVE THE TWO APU ACCESS DOORS TO THE
_______ OUTBOARD SIDE FROM THE FULL OPEN POSITION. THE FULL OPEN POSITION IS WHERE THE APU ACCESS DOOR IS DOWN AND THE TWO HOLD-OPEN RODS ARE CONNECTED TO THE TWO BRACKETS ON THE APU COMPARTMENT BULKHEAD. DAMAGE TO THE ELEVATOR CONTROL SURFACES CAN OCCUR.
 (b)  
Open the left access door to the fully open position and remove the two hold-open rods from the two clips.

 (c)  
Remove the two quick-release pins from the two brackets on the left APU compartment bulkhead.

 (d)  
Connect the two hold-open rods from the left access door to the two brackets and install the two quick-release pins.

 (e)  
Push the right access door up and remove the lanyard from the pin on the aft APU compartment bulkhead.

 (f)  
Open the right access door to the fully open position and remove the two hold-open rods from the two clips.

 (g)  
Remove the two quick-release pins from the two brackets on the right APU compartment bulkhead.

 (h)  
Connect the two hold-open rods from the right access door to the two brackets and install the two quick-release pins.

 C.
Rate Sensor Removal

 S 024-030
 CAUTION: MAKE SURE YOU DO NOT HIT THE AIR INLET PLENUM WITH YOUR HANDS
_______ OR YOUR TOOLS. DAMAGE TO THE AIR INLET PLENUM CAN OCCUR.
 (1)  
Do these steps to remove the rate sensor (4):

 (a)  
Disconnect the pressure tube (7) from the rate sensor (4).

 (b)  
Disconnect the tube assembly (sense line) (18) from the rate sensor (4).

 (c)  
Remove the bolt (5) and washer (12) that attach the rate sensor (4) and bracket (2) to the load compressor scroll housing.

 (d)  
While you hold the rate sensor (4), remove the two bolts (1) that attach the rate sensor (4) and bracket (2) to the load compressor scroll housing.

 (e)  
Remove the rate sensor (4) and bracket (2) from the load compressor scroll housing.

 (f)  
Remove the packing (13) from the rate sensor (4). 1) Discard the packing (13).

 (g)  
Remove the two nuts (3), two bolts (6) and two washers (12) that attach the rate sensor (4) to the bracket (2).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-07
 ALL  ú ú 03 Page 402 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
APU COMPARTMENT  FWD 
SEE  B 
SEE 
A  FWD 

Rate Sensor Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-07
 ALL  ú ú 03 Page 403 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(94)