S 864-003

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6-2 Main Power Distribution Panel
 1) 6K18, APU ALTN CONT

 (b)  
P83 Aft APU Equipment Control and Circuit Breaker Panel 1) APU PRIME CONT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-41-01
 ALL  ú ú 01 Page 401 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 014-022
 (3)  
Open the left APU access door, 317AL, and right APU access door, 318AR:

 (a)  
While you hold the two APU access doors in the closed position, open the six latches on the right access door.

 NOTE: The left access door will open fully and the right
____ access door will drop approximately one inch (2.5 cm) from the fuselage frame when the last latch is opened.
 NOTE: A lanyard is attached to the aft end of the right access
____ door to hold the access door to the APU compartment bulkhead.
 CAUTION: BE CAREFUL NOT TO MOVE THE TWO APU ACCESS DOORS TO THE
_______ OUTBOARD SIDE FROM THE FULL OPEN POSITION. THE FULL OPEN POSITION IS WHERE THE APU ACCESS DOOR IS DOWN AND THE TWO HOLD-OPEN RODS ARE CONNECTED TO THE TWO BRACKETS ON THE APU COMPARTMENT BULKHEAD. DAMAGE TO THE ELEVATOR CONTROL SURFACES CAN OCCUR.
 (b)  
Open the left access door to the fully open position and remove the two hold-open rods from the two clips.

 (c)  
Remove the two quick-release pins from the two brackets on the left APU compartment bulkhead.

 (d)  
Connect the two hold-open rods from the left access door to the two brackets and install the two quick-release pins.

 (e)  
Push the right access door up and remove the lanyard from the pin on the aft APU compartment bulkhead.

 (f)  
Open the right access door to the fully open position and remove the two hold-open rods from the two clips.

 (g)  
Remove the two quick-release pins from the two brackets on the right APU compartment bulkhead.

 (h)  
Connect the two hold-open rods from the right access door to the two brackets and install the two quick-release pins.

 F.
Starter Motor Removal

 S 024-005
 (1)  
Do these steps to remove the starter motor (1):

 (a)  
Put the container below the starter motor.

 (b)  
Remove the two nuts (5), two washers (4) and four washers (3) that attach the two terminal leads (2) to the starter motor (1).

 (c)  
Disconnect the two terminal leads (2) from the two terminals.

 (d)  
Loosen the coupling clamp (7) that attaches the starter motor

 (1)
 to the starter motor adapter.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-41-01
 ALL  ú ú 01 Page 402 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

FWD 
SEE  C  SEE  A 
APU COMPARTMENT  SEE  B  FWD 
A 
1. STARTER MOTOR 
GEARBOX ACCESSORY STARTER MOTOR ADAPTER ALIGNMENT PIN HOLE  ALIGNMENT PIN  2. TERMINAL LEAD (2 LOCATIONS) 4. WASHER (2 LOCATIONS) (2 LOCATIONS) 3. WASHER (QTY 2) 
6. PACKING  TERMINAL (2 LOCATIONS) 
7. COUPLING CLAMP  FWD  (2 LOCATIONS) 5. NUT 
B 
Figure 401 (Sheet 1) Starter Motor Installation 

K03736
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-41-01
 ALL  ú ú 05 Page 403 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

VENT TUBE 
ADAPTER 
9. TRANSFER 
TUBE 
8. BREATHER 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(58)