(b)  
Pull the acoustic lining (3) aft and remove the lining.

 (c)  
Remove the bolts (5), the washers (7 and 9), the bushings (6), and the nuts (8) that attach the inner exhaust duct (3) to the outer exhaust duct (1).

 (d)  
Move the inner exhaust duct (3) aft and remove it from the outer exhaust duct (1).

 TASK 49-81-02-404-009
 3.  Inner Exhaust Duct Installation (Fig. 401)_______________________________
 A. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 3 | Duct Assembly (Inner Exhaust Duct)| 49-81-51 | 01 | 130 | 2.......….......…...................................…...........…......….......1
 B. Access
 (1)  
Location Zone
 317 APU Compartment-Exhaust Duct, LH
 318 APU Compartment-Exhaust Duct, RH

 (2)  
Access Panel
 317AL APU Access Door
 318AR APU Access Door

 C.
Procedure

 S 424-017
 (1)  
Install the inner exhaust duct (3):

 (a)  
Put the inner exhaust duct (3) in the outer exhaust duct (1).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-81-02
 ALL  ú ú 01 Page 403 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  
Install the bolts (5), the washers (7 and 9), the bushings (6), and the nuts (8) that attach the inner duct (3) to the outer duct (1). 1) Tighten the nuts (8) to 360-440 pound-inches (40.7-49.7

 N.m).

 (c)  
Put the acoustic lining (2) in the inner exhaust duct (3).

 (d)  
Attach the acoustic lining (2) to the inner exhaust duct (3) with the bolts, the nuts, and the washers. 1) Install lockwires on the nuts.

 S 414-014
 (2)  
Close the APU access doors:

 (a)  
Do a visual check of the EGT bus bars:
 1) Make sure the bus bars are not damaged.
 2) Make sure no metal parts touch the bus bars.
 3) Make sure the bus bars do not touch each other.

 (b)  
Disengage the support rods for the APU access doors.

 (c)  
Put the support rods in the clips in the inner side of the APU access doors.

 (d)  
Make sure the insulation covers correctly attach to the APU compartment firewall.

 (e)  
Close the APU access doors.

 (f)  
Close the latches on the APU access doors.

 S 864-015
 (3)  
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P83 Panel, E8 Aft Equipment Center
 1) APU PRIMARY CONT

 (b)  
P6 Main Power Supply Panel
 1) 6K18 APU ALTN CONT

 S 864-016
 (4)  Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-81-02
 ALL  ú ú 03 Page 404 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 INNER EXHAUST DUCT - INSPECTION/CHECK
_____________________________________
 1.  General_______
 A.  Inner exhaust duct can move apart from the outer exhaust duct if the bolts and bushings that attach them are worn. This procedure contains the task to measure the bushings for signs of damage.
 B.  To get access to the inner exhaust duct, you must remove the acoustic lining. After the acoustic lining is removed, you must go through the exhaust outlet at the aft end of the airplane.
 TASK 49-81-02-206-001
 2.  Inner Exhaust Duct Inspection (Fig. 601)_____________________________
 A.  References
 (1)  
49-81-03/201, Acoustic Liner

 (2)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(141)