(b)  
Install the plain seal (1) into the load gearbox housing. 1) Make sure the lip on the seal (1) points to the rear of the

 APU. 2) Make sure the seal (1) is installed correctly.

 (c)  
Install the retainer ring (2).

 S 414-019
 (2)  
Install these components:

 (a)  
The APU generator (Ref 24-21-03/401)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-27-05
 ALL  ú ú 01 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (b)  The QAD ring for the APU generator (Ref 24-21-02/401).
 (3)  S 434-022Connect the coupling that attaches the air exhaust duct on the generator to the upper air exhaust duct.
 (4)  S 864-023Remove the electrical power from the airplane (Ref 24-22-00/201).
 (5)  S 434-024Connect the electrical plugs for the applicable generator: (a) Generator No. 1 1) DG2A 2) DG2B (b) Generator No. 2 1) DG3A 2) DG3B
 (6)  S 864-025Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 panel.
 (7)  S 864-026Start and operate the APU for 10-15 minutes at a stable speed with no load applied (Ref 49-11-00/201).
 (8)  S 794-027During the APU operation, examine the engine for leakage.
 (9)  S 414-028Close the APU access doors: (a) Do a visual check of the EGT bus bars: 1) Make sure the bus bars are not damaged. 2) Make sure no metal parts touch the bus bars. 3) Make sure the bus bars do not touch each other.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-27-05
 ALL  ú ú 01 Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  
Disengage the support rods for the APU access doors.

 (c)  
Put the support rods in the clips on the inner side of the APU access doors.

 (d)  
Make sure the insulation covers correctly attach to the APU compartment firewall.

 (e)  
Close the APU access doors.

 (f)  
Close the latches on the APU access doors.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-27-05
 ALL  ú ú 01 Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 FUEL PUMP DRIVE SPUR GEAR SHAFT OIL SEAL -
________________________________________ REMOVAL/INSTALLATION
____________________
 1.  General_______
 A.  This procedure contains the tasks for the removal and the installation for the oil seal on the gear shaft assembly for the fuel pump drive.
 B.  The seal is in the accessory gearbox on the aft end of the gear shaft assembly that operates the fuel pump. You can get access to the oil seal through the APU access doors.
 TASK 49-27-06-004-022
 2.  Fuel Pump Drive Spur Gear Shaft Oil Seal Removal (Fig. 401)________________________________________________
 A.  Special Tools
 (1)  PWC41383 Extractor - Pratt and Whitney Canada Inc
 1000 Marie Victorin
 Longueuil, Quebec
 Canada J4G 1A1
 Attention: Parts Division

 OR
 Kell-Strom Tool Company Inc 214 Church Street Wethersfield, CT 06109 USA
 B.  References
 (1)
12-22-02/301, Auxiliary Power Unit (Oil Change)

 (2)
IPC 49-31-03 Fig. 1

 C.  
Access

 (1)
Location Zone

 318  APU Compartment-Bottom Side of Air Inlet Plenum, Accessory Gearbox Aft Face

 (2)  
Access Panel
 317AL APU Access Door
 318AR APU Access Door

 D.  
Procedure

 (1)
Do this task: "Drain the APU Oil" (Ref 12-22-02/301).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(21)