(2)
D00418 Oil - Aircraft Turbine Engine
C. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 2 | Oil Filter Element | 49-27-03 | 01 | 55 | | | 3 | Packing | | | 45 | | | 5 | Packing | | | 10 | 2.......….......…...................................…...........…......….......1
D. Access
(1)
Location Zones 221 Control Cabin - Left 222 Control Cabin - Right 310 Fuselage - Station 2360 to Station 2792
(2)
Access Panels
317AL APU Access Door - Left
318AR APU Access Door - Right
E.
Procedure
S 424-033
CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY.
_______ IF YOU DO NOT REMOVE THE PROTECTION COVERS, DAMAGE TO THE APU CAN OCCUR.
(1)
Do these steps to install the oil filter element (2):
(a)
Install the oil filter element (2) and then the retainer ring
(1)
in the oil filter cover (4).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-27-03
ALL ú ú 03 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Lubricate the new packing (3) with a light coat of oil.
(c)
Install the packing (3) on the oil filter cover (4).
(d)
Install the oil filter cover (4) on the oil filter housing with the four washers (8) and four nuts (7). 1) Tighten the four nuts (7) to 75-85 inch-pounds (8.5-9.6
newton-meters).
(e)
Lubricate the new packing (5) with a light coat of oil.
(f)
Install the packing (5) on the plug (6).
(g)
Install the plug (6) in the oil filter cover (4).
1) Tighten the plug (6) to 65-75 inch-pounds (7.3-8.5 newton-meters).
(h)
Install the lockwire between the plug (6) and the hole on the oil filter cover (4).
F.
Oil Filter Element Installation Test
S 864-023
(1)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6-2 Main Power Distribution Panel
1) 6K18, APU ALTN CONT
(b)
P83 Aft APU Equipment Control and Circuit Breaker Panel 1) APU PRIME CONT
S 864-024
(2)
Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 overhead panel.
S 794-027
(3)
Do the installation test for the oil filter element:
(a)
Do this task: APU Starting and Operation (AMM 49-11-00/201).
(b)
Operate the APU for a minimum of five minutes.
(c)
During the APU operation, examine the oil filter housing and oil filter cover for signs of oil leakage.
(d)
If you find oil leakage, then do these steps to repair the leakage: 1) Do this task: APU Usual Shutdown (AMM 49-11-00/201). 2) Attach a DO-NOT-OPERATE tag to the APU control switch on
the P5 overhead panel. 3) Repair the cause of the oil leakage. 4) Remove the DO-NOT-OPERATE tag from the APU control switch
on the P5 overhead panel. 5) Do this task: APU Starting and Operation (AMM 49-11-00/201). 6) During the APU operation, examine the oil filter housing and oil filter cover for signs of oil leakage.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-27-03
ALL ú ú 03 Page 405 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
7) If you find oil leakage, do the leakage repair again.
(e) If it is not necessary to do other tasks, do this task: APU Usual Shutdown (AMM 49-11-00/201).
S 614-035
(4)
Make sure the APU oil system is full. To check the oil level, do this task: APU Oil Tank Replenishing (AMM 12-13-02/301).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(15)
