TASK 49-52-03-404-016
 3.  Inlet Guide Vane (IGV) Actuator Installation (Fig. 401)____________________________________________
 A. Consumable Materials
 (1)  D00098 Fuel - Turbine Engine, PWA 522
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-03
 ALL  ú ú 05 Page 403 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 B.  References
 (1)  
49-11-00/201, Auxiliary Power Unit

 (2)  
WDM 49-11-18, 49-52-11

 (3)  
SSM 49-11-01, 49-52-01

 C. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 4 | Packing | 49-31-00 | 01 | 192 | | | 5 | Inlet Guide Vane Actuator | 49-52-03 | 01 | 50 | | | 11 | Packing | 49-16-00 | 02 | 50 | 2.......….......…...................................…...........…......….......1
 D.  Access
 (1)  
Location Zone

 317  APU Compartment-Lower Side of Compressor Case Between Air Inlet Plenum and Compressor Scroll, LH

 (2)  
Access Panel
 317AL APU Access Door
 318AR APU Access Door

 E.  
Procedure

 S 434-036
 (1)  
Install the nipples on the IGV actuator (5):

 (a)  
Remove the plugs from the fuel ports and the drain outlet on the IGV actuator (5) housing.

 (b)  
Install the new packings (4), lubricated with engine fuel, on the nipples (3).

 (c)  
Install the nipples (3) on the IGV actuator (5).

 1)  Tighten the nipples (3) to 65-75 pound-inches (7.3-8.5 N.m).

 (d)  
Install the new packing (11), lubricated with engine fuel, on the nipple (9).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-03
 ALL  ú ú 04 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (e)  Install the nipple (9) on the IGV actuator (5).
 1)  Tighten the nipple (9) to 110-120 pound-inches (12.4-13.5 N.m).
 S 424-022
 (2)  
Install the IGV actuator (5):

 (a)  
Install the IGV actuator (5) on the compressor case with the washers (6) and the nuts (8). 1) Tighten the nuts (8) to 32-36 pound-inches (3.6-4.1 N.m).

 (b)  
Connect the flexible drain line (10) to the IGV actuator (5).

 1)  Tighten the drain line (10) to 270-300 pound-inches (31-34 N.m).
 CAUTION: MAKE SURE THE BOLT HEAD IS ON THE FORWARD SIDE OF THE
_______ ACTUATOR LINK WHEN YOU INSTALL THE BOLT. THIS WILL PREVENT INTERFERENCE OF THE BOLT HEAD WITH THE INLET PLENUM.
 (c)  
Connect the actuator rod (12) to the connector rod (15) with the bolt (16), the washers (17), and the nut (18). 1) Tighten the nut (18) to 65-85 pound-inches

 (7.4-9.6 newton-meters).

 (d)  
Remove the caps from the fuel supply line (2) and the return line (1).

 (e)  
Connect the fuel supply line (2) and the return line (1) to the IGV actuator (5). 1) Tighten the lines (1 and 2) to 90-100 pound-inches

 (10.2-11.3 N.m). 2) Tighten the lines (1 and 2) at the tee connectors to 90-100 pound-inches (10.2-11.3 N.m).

 (f)  
Remove the caps from the P17 electrical connector (7) and the receptacle.

 (g)  
Connect the P17 electrical connector (7) to the IGV actuator (5). 1) Tighten the connector (7) with your hand.

 NOTE: The connector is fully tight when you cannot see
____
 the red color band.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(84)