Loss of the DME 1 Tuning Data
 1. Possible Causes
_______________
 - FMGC-1 (1CA1)

 - RMP-COM/NAV FREQ SEL, 1 (1RG1)

 - INTRG-DME, 1 (2SD1)

 - wiring of the FMGC OWN CB 1 bus from the FMGC 1 (1CA1) to the first
 terminal block

 - wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block

 - wiring of the NAV DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block

 - wiring of the FREQ FUNCT SELECT DATA INP A bus from the DME interrogator 1 (2SD1) to the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 22-83-34-000-001 Removal of the FMGC (1CA1,1CA2)
 AMM 22-83-34-400-001 Installation of the FMGC (1CA1,1CA2)
 AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1,

 1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP)
 (1RG1, 1RG2, 1RG3) AMM 34-14-00-740-001 Interface Test of the IR AMM 34-51-00-740-002 BITE Test of the DME AMM 34-51-33-000-001 Removal of the DME Interrogator (2SD1,2SD2) AMM 34-51-33-400-001 Installation of the DME Interrogator (2SD1,2SD2) AMM 34-55-00-740-002 BITE Test of the VOR/MKR ASM 22-86/02 ASM 23-13/01 ASM 34-51/01
 3. Fault Confirmation
__________________
 A. Test
 Do the BITE test of the DME (Ref. AMM TASK 34-51-00-740-002).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-51-00∞∞∞∞∞∞∞∞∞∞Page 220
 Feb 01/05R
 CES  4. Fault Isolation

_______________
 A. If the test gives the maintenance message FMGC1(1CA1)/RMP1(1RG1)/DME1(2SD1): - on the center pedestal, on the RMP 1, push the NAV and the VOR
 pushbutton switches (the green LED on these pushbutton switches comes on)
 - do the BITE test of the DME (Ref. AMM TASK 34-51-00-740-002).
 (1) If the test does not give the maintenance message
 FMGC1(1CA1)/RMP1(1RG1)/ DME1(2SD1):

 - do the Interface test of the IR (system 1) (Ref. AMM TASK 34-14-00-740-001).
 (a) If the Interface test of the IR gives a maintenance message related of a FMGC 1 failure:
 - replace the FMGC-1 (1CA1) (Ref. AMM TASK 22-83-34-000-001) and (Ref. AMM TASK 22-83-34-400-001).
 1 If the fault continues:
_
 - do a check and repair the wiring of the FMGC OWN CB 1 bus from the FMGC 1 (1CA1) to the first terminal block (Ref. ASM 22-86/02).
 (b) If the Interface test of the IR does not give a maintenance message related of a FMGC 1 failure:
 - replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
 1 If the fault continues:
_
 - do a check and repair the wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block (Ref. ASM 23-13/01).
 (2) If the test gives again the maintenance message
 FMGC1(1CA1)/RMP1(1RG1)/ DME1(2SD1):

 - do the BITE test of the VOR/MKR (Ref. AMM TASK 34-55-00-740-002).
 (a) If the BITE test gives a maintenance message related of a RMP 1 failure:
 - replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
 1 If the fault continues:
_
 - do a check and repair the wiring of the NAV DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block (Ref. ASM 34-51/01).
 (b) If the BITE test does not give a maintenance message related of a RMP 1 failure:
 - replace the INTRG-DME, 1 (2SD1) (Ref. AMM TASK 34-51-33-000-001) and (Ref. AMM TASK 34-51-33-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-51-00∞∞∞∞∞∞∞∞∞∞Page 221
 Feb 01/05R CES

 1_ If the fault continues:
 - do a check and repair the wiring of the FREQ FUNCT SELECT
 DATA INP A bus from the DME interrogator 1 (2SD1) to the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(96)