3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the ATC (Ref. AMM TASK 34-52-00-710-003).
4. Fault Isolation
_______________
A. If there is no display on the ATC/TCAS control unit during the test:
- do the BITE test of the ATC (Ref. AMM TASK 34-52-00-740-004).
(1) If the BITE test gives the maintenance message:
- Do the trouble shooting procedure related to the maintenance message.
(2) If the BITE test does not give a maintenance message:
- replace the CTL UNIT-ATC/TCAS (3SH) (Ref. AMM TASK 34-52-12-000-001) and (Ref. AMM TASK 34-52-12-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-52-00∞∞∞∞∞∞∞∞∞∞Page 231
May 01/05R
CES
R **ON A/C 051-099, 106-149, 201-299, 301-399, 401-499,
TASK 34-52-00-810-820
Malfunction of the ATC1/Mode S Address
1. Possible Causes
_______________
- XPDR-ATC/MODE S, 1 (1SH1)
- ATC/MODE S address pin programming, connector AB
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-52-00-740-004 BITE Test of the ATC AMM 34-52-33-000-001 Removal of the ATC/Mode S Transponder (1SH1, 1SH2) AMM 34-52-33-400-001 Installation of the ATC/Mode S Transponder
(1SH1,1SH2)
ASM 34-52/01
AWM 34-52-05
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the ATC (Ref. AMM TASK 34-52-00-740-004).
4. Fault Isolation
_______________
A. If the test gives the maintenance message WRG : MODE S
ADDRESS/ATC1(1SH1):
- swap the XPDR-ATC/MODE S, 1 (1SH1) and the ATC/MODE S transponder 2 (Ref. AMM TASK 34-52-33-000-001) and (Ref. AMM TASK 34-52-33-400-001).
(1) If the test gives the maintenance message WRG : MODE S ADDRESS/ATC2(1SH2):
- replace the ATC/Mode S transponder that you installed on side 2.
(2) If the maintenance message WRG : MODE S ADDRESS/ATC1(1SH1) is shown again:
- remove the ATC/Mode S transponder 1
- do a check and repair the ATC/MODE S address pin programming, connector AB (Ref. ASM 34-52/01) and (Ref. AWM 34-52-05)
- install the ATC/Mode S transponder 1.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 051-099, 106-149, 201-299, 301-399, ∞∞34-52-00∞∞∞∞∞∞∞∞∞∞Page 232
401-499, Aug 01/05 CES Malfunction of the ATC2/Mode S Address
1. Possible Causes
_______________
- XPDR-ATC/MODE S, 2 (1SH2)
- ATC/Mode S address pin programming, connector AB
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-52-00-740-004 BITE Test of the ATC AMM 34-52-33-000-001 Removal of the ATC/Mode S Transponder (1SH1, 1SH2) AMM 34-52-33-400-001 Installation of the ATC/Mode S Transponder
(1SH1,1SH2)
ASM 34-52/01
AWM 34-52-06
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the ATC (Ref. AMM TASK 34-52-00-740-004).
4. Fault Isolation
_______________
A. If the test gives the maintenance message WRG : MODE S ADDRESS/ATC2 (1SH2):
- swap the XPDR-ATC/MODE S, 2 (1SH2) and the ATC/MODE S transponder 1 (Ref. AMM TASK 34-52-33-000-001) and (Ref. AMM TASK 34-52-33-400-001).
(1) If the test gives the maintenance message WRG : MODE S ADDRESS/ATC1 (1SH1):
- replace the ATC/Mode S transponder that you installed on side 1.
(2) If the maintenance message WRG : MODE S ADDRESS/ATC2 (1SH2) is shown again:
- remove the ATC/Mode S transponder 2
- do a check and repair the ATC/Mode S address pin programming, connector AB (Ref. ASM 34-52/01) and (Ref. AWM 34-52-06)
- install the ATC/Mode S transponder 2.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 051-099, 106-149, 201-299, 301-399, ∞∞34-52-00∞∞∞∞∞∞∞∞∞∞Page 233
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(116)
