- wiring of the ADF 2 INPUT bus from the DMC 2 (1WT2) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-53-00-710-002 Operational Test of the ADF
AMM 34-53-00-740-003 BITE Test of the ADF
AMM 34-53-31-000-002 Removal of the ADF Receiver (2RP1, 2RP2)
AMM 34-53-31-400-002 Installation of the ADF Receiver (2RP1, 2RP2)
ASM 34-53/01
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the ADF (Ref. AMM TASK 34-53-00-710-002).
4. Fault Isolation
_______________
A. If on the two NDs:
. the ADF 2 data do not come into view
. the red flag is shown:
- do the BITE test of the ADF (Ref. AMM TASK 34-53-00-740-003).
(1) If the BITE test gives a maintenance message:
- Do the trouble shooting procedure related to the maintenance message.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 243
May 01/05R CES
(2) If the BITE test does not give a maintenance message:
- replace the RECEIVER-ADF, 2 (2RP2) (Ref. AMM TASK 34-53-31-000-002) and (Ref. AMM TASK 34-53-31-400-002).
(a) If the fault continues:
- do a check and repair the wiring of the BEARING OUTPUT 2 bus from the ADF receiver 2 (2RP2) to the first terminal block (Ref. ASM 34-53/01).
B. If on the CAPT ND only: . the ADF 2 data do not come into view . the red flag is shown:
- make sure that on the center pedestal, on the SWITCHING panel 8VU, the EIS DMC selector switch is at CAPT 3:
(1) If no:
- replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 2 INPUT bus from the DMC 1 (1WT1) to the first terminal block (Ref. ASM 34-53/01).
(2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 2 INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-53/01).
C. If on the F/O ND only: . the ADF 2 data do not come into view . the red flag is shown:
- make sure that on the center pedestal, on the SWITCHING panel 8VU, the EIS DMC selector switch is at F/O 3:
(1) If no:
- replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 2 INPUT bus from the DMC 2 (1WT2) to the first terminal block (Ref. ASM 34-53/01).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 244
May 01/05R
CES (2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 2 INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-53/01).
D. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 245
May 01/05R
CES Loss of the ADF 2 Data on the ND
1. Possible Causes
_______________
- RECEIVER-ADF, 2 (2RP2)
- ANTENNA-ADF LOOP AND SENSE, 2 (3RP2)
- wiring from the ADF loop and sense antenna 2 (3RP2) to the ADF receiver 2 (2RP2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-53-00-710-002 Operational Test of the ADF
AMM 34-53-00-740-003 BITE Test of the ADF
AMM 34-53-11-000-001 Removal of the ADF Loop and Sense Antenna
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(136)
