3. Fault Confirmation
__________________
A. Test Do the operational test of the VOR (system 1) (Ref. AMM TASK 34-55-00-710-001).
4. Fault Isolation
_______________
A. If there is no audio signal on the loud speakers during the test when the VOR1 data are shown on the ND:
- do the BITE test of the VOR/MARKER (system 1) (Ref. AMM TASK 34-55-00-740-002)
(1) If the test gives the maintenance message AMU(1RN)/VOR1(3RS1):
- replace the RECEIVER-VOR/MKR, 1 (3RS1) (Ref. AMM TASK 34-55-31-000-001) and (Ref. AMM TASK 34-55-31-400-001).
(a) If the fault continues:
- replace the AMU (1RN) (Ref. AMM TASK 23-51-34-000-001) and (Ref. AMM TASK 23-51-34-400-001).
1 If the fault continues:
_
- remove the VOR/MKR receiver 1
- remove the AMU
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : ALL ∞∞34-55-00∞∞∞∞∞∞∞∞∞∞Page 245
Feb 01/05 CES
- do a check and repair the wiring from the VOR/MKR receiver 1 to the AMU: from pins AB/7B, 7C to pins AA/8B, 8A (Ref. ASM 34-55/01)
- install the VOR/MKR receiver 1
- install the AMU.
B. Do the test given in Para. 3.
Loss of the VOR1 Data
1. Possible Causes
_______________
- RECEIVER-VOR/MKR, 1 (3RS1)
- wiring between the VOR/MKR receiver 1 and the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 34-55-00-740-002 BITE Test of the VOR/MKR
AMM 34-55-31-000-001 Removal of the VOR/MKR Receiver (3RS1, 3RS2)
AMM 34-55-31-400-001 Installation of the VOR/MKR Receiver (3RS1, 3RS2)
ASM 34-55/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the VOR/MARKER (system 1) (Ref. AMM TASK 34-55-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC1/2 (1WT1/2)/DDRMI (1FN)/VOR1 (3RS1):
- swap the RECEIVER-VOR/MKR, 1 (3RS1) and the VOR/MKR receiver 2 (Ref. AMM TASK 34-55-31-000-001) and (Ref. AMM TASK 34-55-31-400-001).
(1) If the fault stops:
- replace the VOR/MKR receiver that you installed on side 2.
(2) If the fault continues:
- remove the VOR/MKR receiver 1
- do a check and repair the wiring between the VOR/MKR receiver 1 and the first terminal block: for pins AB/13B, 13C (Ref. ASM 34-55/01)
- install the VOR/MKR receiver 1.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : ALL ∞∞34-55-00∞∞∞∞∞∞∞∞∞∞Page 247
Feb 01/05 CES Loss of the VOR1 Interface with the DMC2
1. Possible Causes
_______________
- DMC-2 (1WT2)
- wiring between the DMC2 and the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-004 EIS System Test
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-55-00-740-002 BITE Test of the VOR/MKR
ASM 34-55/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the VOR/MARKER (system 1) (Ref. AMM TASK 34-55-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC1/2 (1WT1/2)/DDRMI (1FN)/VOR1 (3RS1):
- do the SYSTEM TEST of the DMC2 (Ref. AMM TASK 31-60-00-740-004).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(157)
