3. Fault Confirmation
__________________
 A. Do the BITE test of the DME (system 1) (Ref. AMM TASK 34-51-00-740-002).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message DMC1/2
 (1WT1/2)/DDRMI(1FN)/DME1(2SD1):

 - do the EIS system test (for the DMC1) (Ref. AMM TASK 31-60-00-740-004).
 (1) If the test gives a maintenance message related to a DMC1 fault:

 - replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).

 (2) If the test does not give a maintenance message related to a DMC1 fault:

 - remove the DMC1

 - do a check and repair the wiring between the DMC1 and the first terminal block: for pins AA/7A, 7B of the DMC1 (Ref. ASM 34-51/01)

 - install the DMC1.

 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-51-00∞∞∞∞∞∞∞∞∞∞Page 245
 Feb 01/05R CES

 Loss of the DME1 Interface with the DMC2
 1. Possible Causes
_______________
 - DMC-2 (1WT2)

 - wiring between the DMC2 and the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-004 EIS System Test
 AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
 AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 AMM 34-51-00-740-002 BITE Test of the DME
 ASM 34-51/01

 3. Fault Confirmation
__________________
 A. Do the BITE test of the DME (system 1) (Ref. AMM TASK 34-51-00-740-002).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message DMC1/2
 (1WT1/2)/DDRMI(1FN)/DME1(2SD1):

 - do the EIS system test (for the DMC2) (Ref. AMM TASK 31-60-00-740-004).
 (1) If the test gives a maintenance message related to a DMC2 fault:

 - replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).

 (2) If the test does not give a maintenance message related to a DMC2 fault:

 - remove the DMC2

 - do a check and repair the wiring between the DMC2 and the first terminal block: for pins AA/7A, 7B of the DMC2 (Ref. ASM 34-51/01)

 - install the DMC2.

 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-51-00∞∞∞∞∞∞∞∞∞∞Page 246
 Feb 01/05R CES

 Loss of the DME Antenna 2 Signals
 1. Possible Causes
_______________
 - INTRG-DME, 2 (2SD2)

 - ANTENNA-DME, 2 (3SD2)

 - wiring between the DME interrogator 2 and the DME antenna 2

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 34-51-00-740-002 BITE Test of the DME
 AMM 34-51-11-000-002 Removal of the DME Antenna (3SD1, 3SD2)
 AMM 34-51-11-400-002 Installation of the DME Antenna (3SD1, 3SD2)
 AMM 34-51-33-000-001 Removal of the DME Interrogator (2SD1,2SD2)
 AMM 34-51-33-400-001 Installation of the DME Interrogator (2SD1,2SD2)
 ASM 34-51/01

 3. Fault Confirmation
__________________
 A. Do the BITE test of the DME (system 2) (Ref. AMM TASK 34-51-00-740-002).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message DME2 ANTENNA (3SD2):
 - swap the INTRG-DME, 2 (2SD2) and the DME interrogator 1 (Ref. AMM TASK 34-51-33-000-001) and (Ref. AMM TASK 34-51-33-400-001).
 (1) If the fault stops:

 - replace the DME interrogator that you installed on side 1.

 (2) If the fault continues:

 - remove the DME interrogator 2

 - disconnect the coaxial connector from the DME antenna 2 (Ref. AMM TASK 34-51-11-000-002)

 - do a check of the wiring between the DME interrogator 2 and the DME antenna 2: for pin AB/C of the DME interrogator 2 (Ref. ASM 34-51/01).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(104)